Bedienungsanleitung Funai BH2-M200 (Seite 72 von 88) (Englisch)

503524

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Troubleshooting

Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some

simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.

Others

Symptom Remedy

POWER

The power does not turn on. • Check that the AC power cord is connected securely.

• Batteries of the remote control are weak.

The unit turns on automatically without

any operation.

• The unit turns on automatically 2 seconds before the timer recording.

GENERAL

The unit does not function. • “ ” or error message appears if the operation is prohibited.

• Batteries of the remote control are weak or exhausted.

No picture, sound or menu appears on

the screen.

• Check if the connections are made securely and correctly.

• Check if the cables are damaged.

• Check if a correct external input channel is selected on your TV. (See page 18.)

• Check if you have completed “Auto Tuning”. (See page 58.)

“Clock” setting and “Installation” setting

cannot be performed.

• If a recording is in progress, these operations cannot be performed.

The unit does not operate properly. • Moisture has condensed inside the unit. Remove the disc and leave the unit

turned on for about 2 hours until the moisture evaporates. (See page 3.)

The clock display does not appear on

the front panel display.

• Check that the AC power cord is connected securely.

• (In case of power failure) Check the breaker and “Clock” setting.

When you forget the password for

parental lock.

• Enter 4737 to cancel the current password, then create new one.

No image from HDMI connection. • Check the HDMI connection. (Check the status of the HDMI related indications.)

• Check whether the connected monitor device or other device supports HDCP.

(This unit will not output video signals unless the other device supports HDCP.)

• Check the setting of HDMI.

• Check whether the output format of this unit (HDMI FORMAT) matches the

supported input format of other connected device.

• If the unit is connected to the unauthorised display device with an HDMI cable,

the audio and video signals may not be output when playing back a commercial

BD-video or DVD-video.

TV channels cannot be changed. • Check if the connections are made securely and correctly.

• Check if the cables are damaged.

• Try “Auto Tuning”. (See page 58.)

Some settings are lost even though you

followed the procedure correctly.

• If you unplug the AC mains cable while the warning message, “Wait for a

moment...”, is displayed, some settings may be lost. Do not unplug the AC

mains cable while the message is displayed. (It will take about 1 minute.)

Only specific channels do not appear. • The channels may be set to be skipped. (See page 24.)

Though auto tuning was completed,

you cannot watch the DVB channels.

• Check whether an antenna cable is connected correctly and try tuning again.

• If you move to a different area, you need to perform auto tuning again.

The TV channel which you were able to

watch before has disappeared and “No

signal” is displayed.

'8'&A'0DQQM2CIG(TKFC[(GDTWCT[2/

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Funai BH2-M200 Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info