Bedienungsanleitung Funai WV20V6 (Seite 77 von 90) (Englisch, Spanisch)

576269

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

Recording Playing discs EditingGetting started

Changing the

Setup menu

VCR functions Others

Before you start

Connections

Español

xxxx

Others

Troubleshooting

Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.

Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper performance.

Symptom Remedy

•

The power does not turn on. • Check that the AC power cord is connected securely.

• (In case of power failure) Check the breaker.

• Press [TIMER SET] to cancel the timer standby mode.

There is no picture. • Re-connect the connecting cord securely.

• Check if the connecting cords are damaged.

• Check the connection to your TV (page 14).

• Check the RF output channel when you view a TV program using

RF connection.

• Switch the input selector on your TV (such as to “EXT1”) so that

the signal from this unit appears on the TV screen.

TV program reception does not fill

the screen.

• Try to set the channels with “Auto Channel Preset” or “Manual Channel

Preset” in the Setup menu (pages 19-20).

• Select a channel of any TV program using the [CH K / L].

• Press [VIDEO/TV] if necessary.

TV program pictures are distorted. • Adjust TV antenna.

• Adjust the picture (see the TV’s instruction manual).

• Place the unit and TV farther apart.

• Place the TV and any bunched antenna cables farther apart.

TV channels cannot be changed. • Switch the input to TV.

• Connect the antenna cable correctly (page 14).

Playback picture is distorted. • Keep the equipment which may cause electrical disturbances, such

as a cellular phone, away.

The playback picture or TV

program from the equipment

connected through the unit is

distorted.

• If the playback picture output from a DVD player, VCR or tuner

goes through the unit before reaching your TV, the copy-protection

signal applied to some programs could affect picture quality.

Disconnect the playback equipment in question and connect it

directly to your TV.

There is no sound. • Re-connect all connections securely.

• The connecting cord is damaged.

• Check the connections to the amplifier input.

• The input source setting on the amplifier is incorrect.

• The unit is in pause mode or in Slow forward / Slow reverse play.

• The unit is in fast forward or fast reverse mode.

The channel cannot be changed

from the channel you are recording.

• Set the TV’s input to “TV”.

Nothing was recorded even though

you set the timer setting correctly.

• There was a power failure during recording.

• The internal clock of the unit stopped due to a power failure that

lasted for more than 30 seconds. Reset the clock (pages 22-24).

• Disconnect the AC power cord from the AC outlet, and connect it

again.

• The program contains copy protection signals that restricts copying.

• The timer setting overlapped with another setting that has priority.

Timer Recording is not completed

or did not start from the beginning.

• The timer setting overlapped with another setting that has priority

(page 32).

• Disc space was not enough.

Timer Recording is impossible. • Make sure TIMER REC indicator lights up on the front panel of this

unit. If not, press [TIMER SET].

The remote control does not work. • Check the antenna or cable connection to the main unit.

• Check the battery life of the remote control.

• Check if there is an obstacle between the sensor and the remote

control.

• Test the signal output. If OK, then possible remote sensor trouble.

(Refer to “IR SIGNAL CHECK” on page 5.)

• Press [DVD

] or [VCR ], whichever you need. Then, try again.

• Press [TIMER SET] to cancel the timer standby mode.

The unit does not operate properly. • When static electricity, etc., causes the unit to operate abnormally,

unplug the unit and then plug it again.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Funai WV20V6 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info