Bedienungsanleitung Fusion Apollo MS-SRX400 (Seite 8 von 12) (Englisch)

691368

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

Connecting the FUSION PartyBus Device to

a Wireless Access Point

Select > SETTINGS > NETWORK > WI-FI CLIENT >

SSID.

A list of wireless access points within rage appears.

Select the FUSION PartyBus wireless access point.

Select an option:

• To enter the password, select PASSWORD, enter the

password, and select .

• If you are connecting to the wireless access point using

WPS, verify that WPS has been enabled on the access

point, and select WPS.

NOTE: It can take up to two minutes to successfully

connect to the access point after you select WPS.

Select SAVE.

Streaming from a FUSION PartyBus Network

Device

Before you can stream media from a FUSION PartyBus stereo,

you must connect the device to the FUSION PartyBus network

using a wired or wireless connection. See the Apollo RA770

installation instructions.

You can stream media from an Apollo RA770 stereo, but you

cannot stream media from another Apollo SRX400 zone stereo.

NOTE: You cannot stream from a stereo using the Apple AirPlay

source.

Select .

Press and hold the dial to select the PARTYBUS tab.

TIP: You can press and hold to quickly join the FUSION

PartyBus network.

The device shows a list of available FUSION PartyBus

stereos on the network.

Select the stereo you want to stream from.

The Apollo SRX400 zone stereo begins streaming the same

source as the connected FUSION PartyBus device, and a green

border appears around the device screen. All media playback

functions affect both devices.

Stopping Streaming from a FUSION

PartyBus Device on the Network

If you are streaming from a FUSION PartyBus device on the

network, you must disconnect from the device before you can

play local sources on the stereo.

Select .

Select PARTYBUS > LEAVE PARTYBUS.

TIP: You can press and hold to quickly leave the FUSION

PartyBus network.

Network UPnP Playback

This stereo can play content from Universal Plug and Play

(UPnP) devices connected to the network, such as computers

and media servers. You must connect your UPnP device to the

same network as the stereo using a wired or wireless

connection, and you must configure the device to share media

over the network. See the owner's manual from your UPnP

device for more information.

After you have connected your UPnP device to the network and

configured it to share media, the UPNP source appears on the

source selection screen of each stereo on the network

(Selecting a Source, page 1).

General Settings

Select > SETTINGS.

NOTE: When an option button is filled, the option is on. When

the option button is clear, the option is off.

ZONE: Enables you to configure the speaker zone (Speaker

Zone Settings, page 4).

BRIGHTNESS: Adjusts the screen and dial backlight brightness

(Adjusting the Backlight Brightness, page 1).

TUNER REGION: Sets the region used by the FM and AM

sources.

LANGUAGE: Sets the language on the device.

DEVICE NAME: Sets a name for this stereo.

AirPlay PASSWORD: Sets a password that a user must enter

when connecting to the stereo using the AirPlay feature

(Setting an AirPlay Password, page 3).

POWER OPTIONS: Adjusts power settings, such as standby

mode and power-save mode (Power Options, page 4).

NETWORK: Enables you to join and configure the FUSION

PartyBus network settings (Network Settings, page 4).

UPDATE > STEREO: Updates the stereo software.

UPDATE > FACTORY RESET: Resets all settings to the factory

default values.

ABOUT: Shows the software version and other information for

the stereo.

Speaker Zone Settings

Select > SETTINGS > ZONE > ZONE 1.

LOUD: Maintains frequency response at low volumes and

increases perceived loudness at high volumes.

TONE: Sets the treble, middle, and bass tones.

ZONE NAME: Sets a name for this speaker zone to make it

easier to identify.

SUB FREQ: Sets the subwoofer cutoff frequency, which can

enhance the blend of the sound produced by the speakers

and the subwoofer. Audio signals above the selected

frequency are not passed to the subwoofer.

MORE: Sets the volume limit, subwoofer limit, and speaker

balance.

Disabling the Internal Amplifiers

If the speakers are connected to an external amplifier, you can

disable the internal amplifier to reduce power consumption.

Select > SETTINGS > ZONE.

Select INTERNAL AMP ON to clear the option button.

Power Options

Select > SETTINGS > POWER OPTIONS.

NOTE: When an option button is filled, the option is on. When

the option button is clear, the option is off.

POWER SAVE: Disables the LCD backlight after one minute of

inactivity to save battery power.

STANDBY MODE: Enables a low-power standby instead of

turning off the stereo completely. When enabled, the stereo

turns on much faster, but the stereo uses more battery when

in standby mode than when turned off.

SYSTEM OFF: Sends a signal to turn off on all devices

connected to the network.

Network Settings

Select > SETTINGS > NETWORK.

WI-FI OFF: Turns off all Wi‑Fi wireless functions.

4 General Settings

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Fusion Apollo MS-SRX400 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Fusion Apollo MS-SRX400

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info