Bedienungsanleitung Futaba 14MZ (Seite 43 von 127) (Englisch)

29031

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

Conﬁ rm that the rate of the slowest position (0%) of

the stick is 0% (initial setting).

Be sure that when set to high side 100%, the curve

of any condition does not exceed 100%.

Example of pitch curve setting:

1. Call the pitch curve of each condition with

the condition select switch.

*Pitch curve graph display can be switched to pitch angle

direct reading display.

A. Pitch curve (Normal)

Make the pitch at hovering approximately +5

Set the pitch at hovering with the stick position at

the 50% point as the standard.

*Stability at hovering may be connected to the throttle curve.

Adjustment is easy by using the hovering throttle function

and hovering pitch function together.

B. Pitch curve (Idle up 1)

The idle up 1 pitch curve function creates a curve

matched to airborne ﬂ ight.

Set to -7

~+12

as standard.

C. Pitch curve (Idle up 2)

The high side pitch setting is less than idle up 1.

The standard is +8

D. Pitch curve (Hold)

At auto rotation, use the maximum pitch at both

the high and low sides.

[Pitch angle setting example]

Throttle hold: -7

~+12

6. Throttle hold setting

Call the Throttle Hold function from the Model

Menu and switch to the throttle hold condition with

the condition select switch.

Note: At initial setting, the setting mode is the

group mode. Since this function is not used at other

conditions, switch to the single mode before setting.

●Setting to the state which activates the

function

The throttle hold function allows setting for throttle

cut and switching of the function ﬁ xed at the idle

position by switch for training. Either one or both

functions can be performed.

●Hold position setting

This function sets the servo operation position at

throttle hold. (Throttle cut and idle positions)

●Other settings

When you want to link operation with stick

manipulation, the Auto mode can be set.

When you want to adjust the servo speed, adjust

[Speed].

7. Pitch to RUD mixing setting

Use this function when you want to suppress

the torque generated by the changes in the pitch

and speed of the main rotor during pitch operation.

Adjust it so that the nose does not swing in the

rudder direction. However, when using a heading

hold gyro like those shown below, do not use Pitch

to RUD mixing.

Note: When using a GY601, GY502, GY401, or other

heading hold gyro, this Pitch to RUD mixing should

not be used. The reaction torque is corrected at

the gyro side. When operating the gyro in the AVCS

mode, the mixed signal will cause neutral deviation

symptoms and the gyro will not operate normally.

Call the Pitch to RUD mixing function from the

Model Menu, and set the curve for each condition.

(At initial setting, this function is in the "INH"

state. To use it, set it to the "ON" state.)

(17 points curve)

Curve setting of up to 17 points is possible.

However, in the following setting example, a

simple curve can be adjusted by using the [Linear]

curve type.

Note: At initial setting, the setting mode is the group

mode. In this mode, the same contents are set at in

all conditions. When you want to set the selected

condition only, switch to the single mode.

Call the mixing curve of each condition with the

condition select switch.

●Throttle hold curve adjustment

The throttle hold curve is used when performing

auto rotation dives.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 14MZ Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info