Bedienungsanleitung Futaba 2PL (Seite 13 von 22) (Englisch)

28971

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Assembly / Adjustment

Transmitter Set-Up Procedures

*When making these settings adjustments, do so with the motor disconnected

or the engine not running.

Servo Horn Installation Instructions.

1 Connect the receiver, servos, and other components and

then turn on the power switches to transmitter and receiver.

*Both servos will move to the neutral position.

2 At this time install the servo horn in the manner described in

the instruction manual provided with the model this system

will be used in.

Reversing The Servo Operation Direction

Should the servo operate in the opposite direction re-

quired for your application, reverse the direction with the

servo reversing.

E.S.C. MC230CR / MC330CR

NEUTRAL, HIGH, AND BRAKE MAX POINTS SETTINGS

Before setting each point, set the transmitter throttle channel trim to neutral.

Turn on the power in transmitter -> amp order.

Tr ansmitter throttle operation

･Neutral state

･Press the pushbutton switch.

(0.5 secs or longer)

(Confirmation beep sounds)

･Continuous single blink

MC230CR /MC330CR

(Pushbutton switch operation) (Checker LED)

Full High

Full brake

Neutral

point setting

･Full high state

･Press the pushbutton switch.

(Confirmation beep sounds)

･Continuous double blink

･Continuous rapid blink

High point

setting

･Full brake state

･Press the pushbutton switch.

(Confirmation beep sounds.)

･If the LED goes out,

setting is complete.

Brake MAX

point setting

* Since the data is read at the end of setting of all points, the points cannot be set independently.

* If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained.)

* The confirmation beep sounds only when the motor was connected.

If the LED does not go off

but blinks rapidly, setting

was not performed

normally. Repeat setting

from "Neutral point

setting".

Set the steering angle adjustment function (ATV) to

100% and the ABS function and acceleration function

to OFF using the transmitter throttle channel function.

If the steering angle is too large or the ABS and acceleration

functions are on, erroneous operation may occur.

*When using the ABS function, after setting up

the MC230CR / MC330CR, stop the reverse

function, then turn on the ABS function. If the

ABS function is on, the MC230CR / MC330CR

cannot be set up correctly.

(Preparations)

Select the model memory that is not used and reset it to the initial values with the model selection and

model reset functions.

Model number

（1 - 0）

Model name

(Selection key)

Model Selection Model Reset

Push the DT2 lever up or down

for about one second.

All data stored in the current

selected model memory is

erased.

NOR: Normal

REV: Reverse

(Selection key)

Steering Servo Reverse

NOR: Normal

REV: Reverse

(Selection key)

Throttle Servo Reverse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 2PL Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info