Bedienungsanleitung Futaba 6EXAP (Seite 3 von 24) (Englisch)

28983

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

GLOSSARY

It will be helpful to understand the following terms before reading the rest of the manual. The terms are not in alphabetical

order, but are in a logical order that prepares the reader for understanding the next term.

Reversing (servo reversing) -

A function that allows the user to determine the direction of response of each servo. If, after

hooking up the servos, a control on the model responds in the wrong direction, the user may change the servo's direction so

the control responds correctly.

Throw -

When speaking of a control surface (such as an elevator or aileron), the throw is

the distance the surface moves. Control surface throw is usually measured at the trailing

edge of the surface and is expressed in inches or millimeters. The model in the diagram has

1/2" [13mm] of up elevator throw. Throw can also refer to the distance a servo arm (or

wheel) travels.

Dual rate (D/R) -

On the 6EXAP the dual rate switch allows you to instantly switch, in flight,

between two different control throws for the aileron, elevator and rudder. Often, different

control throws are required for different types of flying. (

“Low” throws may be required for

flying at high speeds where the model

’s response becomes more sensitive, and “high”

throws may be required for aggressive aerobatic maneuvers or landing or flying at lower

speeds where the model's response becomes less sensitive.)

End point adjustment (E.P.A.) -

Sets the overall, maximum distance the servo rotates in either direction. (No matter where

the dual rates are set, the servo will never travel beyond the limit set by the end point adjustment.)

Exponential -

Normally, servos respond proportionally to control stick input from the transmitter (e.g., if the stick is moved

halfway, the servo will move halfway). However, with

“exponential,” the servo can be made to move more or less than initial

stick movement (less servo movement is more common). Exponentials are commonly used to

“soften,” or decrease initial

servo travel for the ailerons, elevators and rudder. This way, initial control stick inputs from the pilot result in small servo

movement for a smoother flying airplane.

(Dual rates adjust the amount

amount

of servo travel. Exponentials determine where

where

most of the travel will occur.)

Mixing -

Two (or more) servos can be made to operate together either by mechanically joining the wires (with a Y-connector)

or by electronically

“joining” them through programming functions in the transmitter. When servos are electronically joined via

programming, they are said to be

“mixed.” Unlike joining servos with a Y-connector, when servos are mixed electronically they

can be made to move in opposition. Additionally, each servo

’s end points can be independently set.

CONTENTS AND SPECIFICATIONS

Transmitter: T6EXAP

T6EXAP Transmitter with programmable mixing and 6-model

memory.

Transmitting on 35, 40, 41, or 72 MHz band.

Operating system: 2-stick, 6-channel system

Modulation: FM(PPM) and PCM

Power supply: 9.6V NT8S600B Ni-Cd battery or 12V alkaline battery

Current drain: 250mA

Receiver: R127DF or R136F

R127DF/R136F narrow band, FM 7/6 channel receiver.

Receiving on 35, 40, 41, or 72 MHz band.

Type: FM, Dual conversion/FM, Single conversion

Intermediate frequencies: 455kHz, 10.7MHz/455kHz

Power requirement: 4.8V or 6V

Current drain: 9.5mA @ 4.8V

Size: R127DF- 1.39x2.52x0.82" (35.3x64.0x20.8mm)/

R136F- 1.31x1.98x0.71" (33.4x50.3x18.1mm)

Weight: R127DF- 1.5oz (42.5g) / R136F- 0.98oz (27.8g)

Servos: S3004 or S3003

S3004 ball bearing/S3003 standard servo with mounting

hardware and servo arm assortment

Control system: Pulse width control,1.52ms neutral

Power requirement: 4.8 or 6V (from receiver)

Output torque: 44.4oz-in [3.2kg-cm] @4.8V

Operating speed: 0.23sec/60

˚@4.8V

Size: 1.59x0.78x1.41" [40.4x19.8x36mm]

Weight: S3004- 1.3oz (37.2g) / S3003- 1.3oz (38.0g)

Servos: S3151

S3151 Digital standard servo with mounting

hardware and servo arm assortment

Control system: Pulse width control,1.52ms neutral

Power requirement: 4.8 (from receiver)

Output torque: 43.1oz-in [3.1kg-cm] @4.8V

Operating speed: 0.21sec/60

˚@4.8V

Size: 1.59x0.79x1.42" [40.5x20x36.1mm]

Weight: 1.48oz (42g)

Other components:

Switch harness

9"[200mm]aileron extension cord (to facilitate quick

connecting and disconnecting of aileron servo with

removable wing)

Instruction manual

*Specifications and ratings are subject to change without notice

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXAP Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info