Bedienungsanleitung Futaba 6EXHP (Seite 11 von 24) (Englisch)

28987

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

PULS Modulation select function

The Modulation select function is used to select the

PPM or PCM mode of transmission, to

match the receiver being used (PPM-Pulse Position Modulation, also called FM for Frequency

Modulation, and PCM-Pulse Code Modulation).

To select modulation:

1. Access the Model Select function in the programming mode (by pressing the MODE and

SELECT keys simultaneously and holding them down for one second). Use the DATA

INPUT lever to select the model memory you wish to modulation select.

2. Push SELECT key twice after seeing on the screen the model memory where you want to

set modulation, then you will see “PULS” on the screen.

3. To select PCM modulation, push the DATA INPUT lever up. The

“PCM” is displayed. To

select PPM modulation, push the DATA INPUT lever down. The

“PPM” is displayed.

4. To get the transmitter to operate in the new mode, switch transmitter power off and then on.

The small indicator will indicate the mode, either PPM or PCM.

Model name function

Assign a name to the model memory. By giving each model a name that is immediately recognizable, you can quickly select

the correct model, and minimize the chance of ﬂying wrong model memory that could lead crash.

1. Access the Model Select function in the programming mode (by pressing the MODE and

SELECT keys simultaneously and holding them down for one second). Use the DATA

INPUT lever to select the model number you wish to change.

2. Push SELECT key three times after seeing on the screen the model memory where you

want to set the model name, then you will see the model name on the screen.

3. Choose a character for the ﬁrst digit by using DATA INPUT lever. Then move to the next digit

by pressing the SELECT key and choose a character in the same way. Continue choosing

characters for the third and fourth digits. You can use up to four characters for the name.

REVR Servo Reversing

The servo reversing function is used to change the direction that a servo responds to a control input from the transmitter

(stick or switch). After using the reversing function, check all the controls on the model to be certain they are operating in the

correct direction and that you did not inadvertently reverse a servo other than the one intended. Reversing the wrong servo (and

not checking the response of the controls before each ﬂight) may be the most common cause of a crash!

To reverse a servo:

1. Enter the programming mode and use the MODE key to access the

REVR function.

2. Use the SELECT key to select the channel you wish to reverse.

3. Push the DATA INPUT lever downward to reverse the servo (REV), or push the lever upward

to make the servo operate normally (NOR). The arrow will indicate the condition of the servo

(normal or reversed).

4. Use the SELECT key to display other channels to be reversed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXHP Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info