Bedienungsanleitung Futaba 6XA (Seite 25 von 64) (Englisch)

28989

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

servo arm so that the throw is adjusted in the

90-100% range.

19. To set the right aileron’s LEFT motion,

move the aileron stick all the way to the left

and hold it. The letters “

L/D” should appear

next to the flashing percent sign (as shown in

the figure above). Again listen and hit the

minus

DATA INPUT key until the buzzing

stops. If the servo is not buzzing, leave the

setting at 100%. You may wish to increase or

decrease this number depending on how

rapidly the model rolls to the left. One

possible setting is roughly 9/16” (14-15 mm)

travel in both directions. (Remember, you’re

only setting the right aileron if you have the

flaperon function turned on. You set the other

aileron’s travel in channel 6’s ATV.)

20. To set the UP elevator motion, press on

the

CURSOR

key until the indicator moves

underneath channel 2, as shown. Now move

the right stick all the way to the transmitter

bottom and hold it. The letters “

R/U” should

appear next to the flashing percent sign (as

shown in the figure above). Again listen for a

buzzing sound to indicate the servo is stalling,

and hit the minus

DATA INPUT key until the

buzzing stops. If the servo is not buzzing,

leave the setting at 100%. You may wish to

increase or decrease this number depending on

how tightly the model does an inside loop (or

whether it snap rolls when it shouldn’t).

flashing

Changes to

"L/D" with AIL

stick motion

21. Repeat the previous step for DOWN

elevator by moving the stick all the way to the

top of the transmitter, full “down” elevator.

Check for binding and adjust the percentage

as before. The elevator settings should be

adjusted so that the elevator travel is roughly

9/16” (15 mm).

22. To set the throttle position at IDLE, press

on the

CURSOR key until the indicator moves

underneath channel 3. Now move the throttle

stick all the way to the transmitter bottom and

hold it. The letters “

R/U” should appear next

to the flashing percent sign. Listen for a

buzzing sound to indicate the servo is stalling,

and hit the minus

DATA INPUT

key until the

buzzing stops. If the servo is not buzzing,

leave the setting at 100% or increase it as

necessary to fully close the throttle. You may

wish to increase or decrease this number

depending on whether you can shut off the

engine using throttle at idle and the trim tab.

23. To set the FULL throttle position, move

the throttle stick all the way to the transmitter

top and hold it. The letters “

L/D” should

appear next to the flashing percent sign.

[Notice that the T6XAs/XHs transmitter

thinks of throttle stick positions to the reverse

of the way it seems, in that with the throttle

stick fully forwards — “up” towards the

transmitter top, is the Down position.] Listen

for a buzzing sound to indicate the servo is

stalling, and hit the minus

DATA INPUT key

until the buzzing stops. If the servo is not

buzzing, leave the setting at 100% or change it

as necessary to fully open the throttle.

24. To set the RIGHT rudder motion, press

on the

CURSOR key until the indicator moves

underneath channel 4. Now move the left

stick all the way to the transmitter right and

hold it. The letters “

R/U

” should appear next

to the flashing percent sign. Listen for a

buzzing sound to indicate the rudder servo is

stalling, and hit the minus

DATA INPUT key

until the buzzing stops. If the servo is not

buzzing, leave the setting at 100%. You may

wish to increase or decrease this number

depending on how strongly the model reacts

when the rudder is deflected. Now move the

stick to the left side, and repeat the setting

procedure for left rudder. The rudder travel

should be set to roughly 45 degrees on both

sides.

23. In the same manner as described above,

be sure to set

ATV values for channels 5

(landing gear) and 6 (second aileron), if you

have either.

– 20 –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6XA Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba 6XA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info