Bedienungsanleitung Futaba 9CPsuper (Seite 19 von 109) (Englisch)

29049

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

WARNING & ERROR DISPLAYS

An alarm or error indication may appear on the display of your transmitter for several reasons, including when the trans-

mitter power switch is turned on, when the battery voltage is low, and several others. Each display has a unique sound

associated with it, as described below.

MODEL SELECTION ERROR: Warning sound: 5 beeps (repeated 3 times)

The MODEL SELECTION warning is displayed when the transmitter attempts to load a model memory from a memory

module (optional CAMPac) that is not currently plugged into the transmitter. When this occurs, model No. 01 is automati-

cally loaded.

Do not fly until the proper model is loaded into memory! Reinsert the memory module, and

recall the desired setup using the model select function.

LOW BATTERY ERROR: Warning sound: Continuous beep until transmitter is powered off.

The LOW BATTERY warning is displayed when the transmitter battery voltage drops below 8.5V.

Land your model as soon as possible before loss of control due to a dead battery.

MIXER ALERT WARNING: Warning sound: 5 Beeps (repeated until problem resolved or overridden)

The MIXER ALERT warning is displayed to alert you whenever you turn on the transmitter with any

of the mixing switches active. This warning will disappear when the offending switch or control is

deactivated. Switches for which warnings will be issued at power-up are listed below:

ACRO:Throttle cut, idle-down, snap roll, airbrake GLID:Butterfly, Start and Speed mixing HELI:Throttle cut, throttle hold, idle-up

If turning a switch OFF does not stop the mixing warning: When the warning does not stop even when the mixing switch

indicated by the warning display on the screen is turned off, the functions described previously probably use the same

switch and the OFF direction setting is reversed. In short, one of the mixings described above is not in the OFF state. In this

case, reset the warning display by pressing both S

ELECT BUTTONS simultaneously. Then change one of the switch settings

of the mixings duplicated at one switch.

BACKUP ERROR: Warning sound: 4 beeps (repeated continuously)

The BACKUP ERROR warning occurs when the transmitter memory is lost for any reason. If this occurs, all of the data will

be reset when the power is turned on again.

[Note] At this warning display, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.

Do not fly when this message is displayed — all programming has been erased and is not avail-

able. Return your transmitter to Futaba for service.

MEMORY MODULE INITIALIZE DISPLAY

This warning appears when an (optional) CAMPac memory module is used in the transmitter for the first time. When the

ODE BUTTON is pressed, initialization of the module begins, after which the memory module can be used. Once the

module is initialized, the display will not appear again.

The 9C super CANNOT convert data from other radio types (ie. 8U, 9Z). Installation of a CAMPac with data from

another radio type will result in reinitialization of the CAMPac and loss of all data.

RF MODULE WARNING: Warning sound: A single long beep. The single beep lets you know that the RF module has been

removed from the transmitter, or is not being read properly. The green RF light also goes out.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9CPsuper Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info