Bedienungsanleitung Futaba 9CPsuper (Seite 88 von 109) (Englisch)

29049

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

HELI-SPECIFIC ADVANCE MENU FUNCTIONS

THR-HOLD: This function holds the engine in the idling position and disengages it from the T

HROTTLE STICK when SWITCH

E (9CH) or G (9CA) is moved. It is commonly used to practice auto-rotation.

Prior to setting up THR-HOLD, hook up the throttle linkage so that the carburetor is

opened fully at high throttle, then use the digital trim to adjust the engine idle

position. To have THR- HOLD maintain idle, move the T

HROTTLE STICK to the idle

position, then move the hold SWITCH on and off and keep changing the offset value

until the servo does not move. To lower the engine idle speed, or if you want to shut

off, input a more negative number.

Adjustability:

Idling position: Range of -50% to +50% centered about the throttle idle position to get the desired engine RPM.

Rudder offset:Offsets the tail rotor pitch. Keeps the fuselage from rotating in throttle hold.

Time delay: A rudder offset time delay may be set up within the DELAY function (see p. 92) to ease in rudder and

prevent tail wag.

Throttle curve: Since the throttle is moved to a single preset position, no curve is available for THR-HOLD.

Collective pitch curve: Independent curve, typically adjusted to create a blade pitch range of -4% to +10% to +12%,

Revo. mix: Since revo. mix adjusts for torque from the engine, no revo. mix is available for THR-HOLD .

Priority: The throttle hold function has priority over idle-up. Be sure that the throttle hold and idle-up S

WITCHES are in the

desired positions before trying to start the engine. (We recommend starting your engine in throttle hold for safety reasons.)

Gyro: Gyro programming includes an option to have a separate gyro setting for each condition, including THR-HOLD .

This avoids the potential problem of the user being in the wrong gyro setting when going to THR-HOLD , resulting in an

improper rudder offset and the model pirouetting.

GOAL of EXAMPLE: STEPS: INPUTS:

Set up throttle hold.

Determine desired throttle position by

idling engine, turn on THR-HOLD , and

adjust percentage as required to reach

the desired running point.

Where next?

Open THR-HOLD function.

Activate the function.

Set desired engine position.

Optional: set up a rudder offset. (If a

slowed reaction is desired, go to DELAY.)

Close.

for 1 second.

(If basic, again.)

to THR-HOLD.

to OFF.

to desired percent.

to OFF.to desired offset.

PIT-CURVE for THR-HOLD: see p. 90.

DELAY for THR-HOLD (to ease collective pitch response): see p. 92.

GYRO setup: see p. 95.

Setting up the Idle-Ups: Throttle and Collective pitch Curves and Revo. Mixing

(TH-CURVE, PIT-CURVE, REVO. MIXING) for idle-ups: see p. 90.

D/R,EXP

: see p. 35.

is automatically activated with THR-HOLD.

•

Switch assignment: Assigned to SWITCH G (9CA) or E (9CH) down.

Adjustable in the SW SELECT (T-HOLD item).

(2-position type switch only)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9CPsuper Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info