Bedienungsanleitung Futaba 9VAP (Seite 20 von 60) (Englisch)

29043

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

ADJUSTMENTS AND FLIGHT TECHNIQUES

DUAL RATE

Dual Rate functions allow the modeler to switch servo travel limits in flight, thus varying

the control sensitivity for different flight conditions or maneuvers.

• Dual Rate functions are available on CH1 (Aileron), CH2 (Elevator), and CH4 (Rudder).

• Dual Rate ON (Low Rate) limits can be adjusted from 30% to 100% of full throw.

•

servo

travel

reduced by

ATV,

the D/R ON throw

will

30%

100% of the

limit

set

ATV

(in

D/R OFF). If AFR is used, the D/R ON limit is unaffected, and will be 30% to 110% of normal (full)

throw.

• Dual Rate ON limits can be adjusted independently in each direction from neutral.

•There are three D/R ON/OFF Switches. Control of the three D/R functions can be assigned to these

switches in any combination the modeler desires, or D/R functions can be switched ON and OFF auto-

matically according to the position of the Throttle stick.

•The

ON/OFF directions

the

D/R

Switches can

reversed

using

the

PARAMETERS program screen

(See page 43).

• In the AUTO D/R mode, the D/R functions can be turned ON and OFF according to the position

(adjustable) of the throttle stick.

•The

Trimmer

Panel

has

D/R

sub trimmers for CH1 (AIL) and CH2 (ELV). The D/R ON limits

can

trimmed ± 25% of the amount set on the screen using these trimmers. The characters in ( ) on the far

right

side

the

screen

(CH1 and CH2

only)

indicate

the

actual

set

amount

(the

amount

set

with

the

program keys ± the sub trimmer setting).

Setting Method

1) Select the EDIT screen, then select the DUAL

RATE screen with the program key.

2) Select the channel to be set with the

cursor key.

3) Move the cursor to the

position with the

or cursor key and press the or

program key to activate or deactivate the

D/R function for that channel.

key is pressed, "ON"or "OFF"

will be displayed in the "INH" position, de-

pending upon the position of the pertinent

D/R ON/OFF switch.

and cursor keys, move the

cursor to the L/D or R/U position and set

the

desired D/R ON throw with the or

program keys. Pressing the pro-

gram key will return the set limit to 100%.

100%.

"sw" position with the or key and

selecting switch No. 1, 2, or 3 with the

,or

program key.

4) When the

The D/R ON/OFF Switches are designated

numbers as follows:

1 ... Aileron D/R

As designated on the

transmitter front.

2 ... Elevator D/R

3... Rudder D/R

Each switch may be used to control one, two, or

all three D/R functions as desired.

7) Field adjustment of the D/R ON limits is

convenient using the AIL and ELE. D/R sub

trimmers on the trimmer panel. The adjust-

ment range is ± 25% of the amount set with

the program keys. A tone will sound at the

neutral (sub trim amount = 0) position of

each sub trimmer.

5) Using the

6) Select the desired ON/OFF Switch for each

D/R function by movinq the cursor to the

[18]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9VAP Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info