Bedienungsanleitung Futaba 9ZAP_part2 (Seite 5 von 78) (Englisch)

29045

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Airplane Section

RUDDER COUPLING (A->R)

This function is used to mix rudder operation

with aileron operation automatically, to make

realistic, coordinated turns. It is especially effec-

tive when turning and banking scale models or

large models that resemble full-sized aircraft. This

mixing

keeps

the

fuselage aligned

into

the

wind

and helps to make what is called "coordinated

turns."

The function allows you to set up the left and

right mixing rates independently. Furthermore,

mixing can be turned on and off during flight by

setting a switch, or it may be set to stay on all the

Setting Up Rudder Coupling

Activation of command

In the Condition Menu, press the

A->R

key to get the

AIL TO RUD menu, as shown below. Use the A

key to activate mode setting, then press the ACT or

INH

keys ( F and G ) to activate or inhibit rudder

coupling.

time if the function is activated (ACT) without

setting an ON/OFF switch. Also, it is possible to

adjust the amount of rudder coupling in-flight, by

setting a volume control.

Mode setting

Mixing i—— Left side

rate

setting I—— Right side

ON/OFF switch

setting

Trimming volume

setting

Return to

Condition screen

Mode Selection Values in ( ) are the mixing rate, including the trim volume.

Setting the Mixing Ratio — Left and Right

You now set the amount of mixing for left aileron

command. Press the C key to activate mixing ratio for

the Left direction and set the value with the numeric keys

F to M . The number keys 0 through

100

input the

value directly. The + and - keys increase or decrease

the value by 1. The +/- key may be used to reverse the

throw direction.

If you are not sure what you are changing, hold the

stick to one side and press different keys — if there is no

effect, move the aileron stick to the other side and con-

tinue. Your setting may vary from -100 to +100%. the

initial value is+50%.

Now set the amount of mixing for the Right aileron

command. Press the

key to activate mixing ratio for

the Right direction and set the throw with the numeric

keys as before.

On/Off Switch Setting

On initial setting, an activation switch for rudder

coupling is not set. meaning that once activated, it is on

all the time. If you would like to set a switch to turn it on

and off, call the Switch Setting screen by pressing the

SWT P

key. Then use the keys to choose the desired

switch location and on direction. For more information

on the switch setting method, see page 37).

Trim Volume setting

You may set up the Rudder coupling function so that

its effect may be changed in flight by moving a trim con-

trol. The trim control adjusts the volume within ±25% of

the set mixing rate. This option is not activated at initial

setup.

Call the volume setting screen by pressing the

VOL

key, and select the desired control using the screen

menus (for a description of the volume setting method,

see page 37).

Use the END (N) key to leave this menu.

Airplane Section, Page 81

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part2 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info