Bedienungsanleitung Futaba 9ZHP_part2 (Seite 10 von 78) (Englisch)

29053

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Airplane Section

FLAP-ELEVATOR

Mix (F-E)

This

function

used

compensate

for

trim

changes when flaps are deployed for show flight or

landing by mixing in a small movement of elevator.

The elevator should be adjusted to move only a

small deflection amount: too much elevator can

make the model difficult to control.

The amount of correction can be adjusted sepa-

rately for both positive and negative flap inputs,

and the neutral mixing position can be offset from

the flap neutral position. Flap-to-elevator mixing

can be turned on and off during flight by setting a

switch, but if an ON/OFF switch is not set, it

remains on all the time. The amount of mixing can

be changed by setting a volume control.

Setting Up Flap-to-Elevator Mixing

Activation of command

In the Condition Menu, press the

F-E

key to get the

FLP TO ELE menu shown below.

Mode setting

Offset amount setting

Mixing

rate

setting

ON/OFF switch

setting

Trimming volume

setting

Return to Condition

screen

Down side

Up side

Mode Selection Rate including volume adjustment

Use the A ( ) key to activate mode setting, then press

the ACT or INH

keys

(F and G)

activate

inhibit flap-to-elevator coupling.

Offset Position Setting

Use the B key to activate offset setting mode.

Then set the flap control to the offset position, and

press the SET key F to store the desired position in

memory.

Setting the Mixing Ratio — Down and Up Side

You now set the amount of mixing for down flap com-

mand. Press the C key to activate mixing ratio for the

down direction and set the value with the numeric keys

E to M .

The number keys 0 through

100

input the

value directly. The + and - keys increase or decrease

the value by 1. The +/- key may be used to reverse the

throw direction. Your setting may vary from —100 to

+100%, the initial value is set to +50%.

Now set the amount of mixing for the up elevator

command. Press the D key to activate mixing ratio for

the Up direction and set the throw with the numeric keys

as before.

On/Off Switch Setting

Initially an activation switch for is not set, meaning

that once activated, this function is on all the time. If you

would like to set a switch to turn it on and off, call the

Switch Setting screen by pressing the

SWT P

key.

Then use the keys to choose the desired switch location

and on direction. For more information on the switch

setting method, see page 37.

Trim volume setting

You may set up the Flap-to-Elevator mixing so that its

effect may be changed in flight by moving a trim control.

The trim control allows you to adjust the volume within

±25% of the set mixing rate, which can be handy for

getting the best value while flying the model. This option

is not activated at initial setup.

Call the volume setting screen by pressing the VOL

O key, and select the desired control using the screen

menus (for a description of the volume setting method,

see page 37).

Use the

END

N key to leave this menu.

Airplane Section, Page 86

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part2 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info