Bedienungsanleitung Futaba 9ZHP_part2 (Seite 13 von 78) (Englisch)

29053

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Airplane Section

FLAPERONS

(FPN)

This function allows you to program the

ailerons to work in the same direction, giving a

flap response as well as aileron control (see figure).

For good square maneuvers, and landing, both

ailerons can be raised and lowered simultaneously.

While this function is on, regular aileron operation

is always present.

The Flaperon function requires two separate

channels: Receiver CH1 (aileron 1/flap 2) and CH6

(aileron 2/flap 1) are the operating channels. The

Aileron 1 and Aileron 2 left and right deflection

angles can be adjusted independently, making it

easy to apply differential to the ailerons. With

differential, the up side travel is set to around 5%

larger than the down travel.

You may also adjust the

Flap

1 and Flap 2

throws independently, and you can set the flap

trim

rate

large

small

you

like.

Also,

the

flap trim offset can be adjusted, allowing you to

freely change the flap neutral angle.

Aileron operation

Flap operation

Setting Up Flaperons

Activation of command

In the Condition Menu, press the

FLP

key to get the

FLAPERON menu as shown below. Use the A key

to activate mode setting, then press the

ACT

INH

keys

(F and G) to

activate or

inhibit

the

function.

Mode setting

Aileron 1 Left

Side Travel

Aileron 2 Left

Side Travel

Flap 2 Travel

Setting

To Next Screen

Aileron 1 Right

Side Travel

Aileron 2 Right

Side Travel

Flap 1 Travel

Setting

Return

condition menu

Mode Selection

Setting the Aileron 1 Travel

You now set the left-side travel for Aileron 1. Press the

key to activate left travel setting for Aileron 1 and set

the travel with the numeric keys E to M . The number

keys 0

through 100 input the

value

directly. The +

and - keys increase or decrease the value by 1. The

+/- key may be used to reverse the throw direction.

If you are not sure what you are changing, hold the

stick to one side and press different keys — if there is no

effect, move the aileron stick to the other side and con-

tinue. Your setting may vary from —120 to +120%, with

an initial value of +100%.

Now set the right-side travel for Aileron 1. Press the

key to activate Aileron 1 right travel setting and set

the travel with the numeric keys as before.

Setting the Aileron 2 Travels

This procedure

repeated for Aileron 2.

Press

theC

key to activate left travel setting for Aileron 2 and set the

travel with the numeric keys Eto M as before.

Now set the right-side travel for Aileron 2. Press the

P key to activate Aileron 2 right travel setting and set

the travel as before.

Setting the Flap Travels — 1 and 2

You now

set

the

travel

for

Flap

Press

the D key

activate travel setting for Flap 2 and set the travel with

the numeric keys E to M . Your setting may vary from

-100 to +100%, with an initial value of +100%.

Now set the travel for Flap 1. Press the

key to

activate Flap 1 travel setting and set its travel with the

numeric keys. Its initial value is -100%.

Airplane Section, Page 89

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part2 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info