Bedienungsanleitung Futaba 9ZHP_part2 (Seite 26 von 78) (Englisch)

29053

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Helicopter Section

To set this feature, call the Pitch->R udder P->R

from the Condition Menu. The Normal setting is

used during hover, so it should be set to match take-

off, landing, and constant speed vertical climbing.

Normal Setting:

Select the normal flight conditions by turning off

all the flight condition switches. Set the rudder mix-

ing curve to the following values (initial settings):

17 Rudder->Throttle Mix Setting

Rudder->Throttle

R->T

mixing is effective in

hovering eight, nose in circle, top hat, pirouette, and

other aerobatics. It should be set so that at half-

throttle, if the rudder stick is operated, the rotor

speed is maintained to keep altitude constant.

Idle-up 1 Setting:

These settings are used in 540° stall turns, loop-

ing, and rolling stall turns and is set to be straight

ahead when the model is pointing directly into or

away from the wind. Call the Idle-up 1 flight condi-

tions by moving switch E to the 0 (center) position.

Set the rudder mixing curve to the following values:

When these values are input, the rudder is offset

at the half-throttle position.

Idle-up 2 Setting:

These settings are used in rolls. Activate the Idle-

up 2 flight conditions by moving switch E to the 1

(forward) position. Set the rudder mixing curve to

the following values:

The rudder is offset at the half-throttle position.

Throttle Hold Setting:

Throttle Hold settings are intended to keep the

model pointed straight ahead during linear autorota-

tion. The tail rotor pitch angle is nearly 0°. Set the

Throttle Hold flight conditions by moving switch G

to the 1 (forward) position. Set the rudder mixing

curve to the following values:

For normal models, commanding right rudder

should increase throttle slightly, while using left

rudder should decrease throttle slightly.

To set this feature, return to the Normal flight

condition.

Press

the Rudder->Throttle

R->T

from

the Condition Menu. Press the

ACT

button to acti-

vate it, and set the Left value to -10%, and the

Right value to +10%.

18 Trim Offset Setting

The Trim Offset

TOF

setting should be adjust-

ed for Idle-up 1 and Idle-up 2. Aileron, elevator, and

rudder are offset so that the model flies straight

ahead during normal flight.

Call the Idle-up 1 or 2 flight condition by setting

Switch E to the 0 (center) position. Press the TOF

button from the Condition menu. Recommended

settings for aileron and elevator offsets are 6% to

10%. A delay can be set with the digital trim

TRM

function.

Rudder offset is set by the Pitch->Rudder func-

tion set previously, so is not set here.

Delay Settings

Set the amount of delay for each flight condi-

tion. We recommend the following settings:

Normal .......

20%

Idle-up

.......

20%

Idle-up

2. ......20%

Throttle Hold .. .. 60%

The delay for Throttle hold should be large, be-

cause the rudder angle changes significantly during

flight condition changes.

Helicopter Section, Page 102

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part2 Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info