Bedienungsanleitung Futaba ATTACK_4 (Seite 3 von 6) (Englisch)

29013

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

Neck strap bracket

Bracket for neck strap. (Neck strap is sold separately.)

Antenna

Strong

telescoping

antenna. Extend

its

full

length

when using the transmitter.

Handle

Use this bar to carry the transmitter.

Nonslip adjustable lever head

The length of the lever head can be adjusted to suit the

operator.

in the arrow direction, and adjust the head to

the most comfortable length, then lock it by

turning it in the direction opposite the arrows. Fig. 3

and

, by turning them

Lever head

Unlock lever heads

Charging jack

Use this jack for charging.

Transmitter crystal

Battery cover

18 Servo reversing switches

Using the servo reversing switches

• The left side of each switch is the normal position.

• The servo reversing switches reverse the direction of opera-

tion of the servos.

Adjust to the length of your hand.

Charging of transmitter and receiver Nicad batteries

Recharge the receiver and transmitter Nicad batteries as

shown in Fig. 4.

Fig.

Aileron servo

reversing switch

NORM-> Normal

REV-> Reverse

After linkage is complete, inspect the servos. If the direction of

operation of the stick lever and the direction of operation of a

servo are opposite, switch the appropriate servo reversing switch.

Rudder servo

reversing switch

Throttle servo

reversing switch

Elevator servo

reversing switch

• Connect the charging plug of the dual charger to the trans-

mitter charging jack. Connect the Rx-connector of the dual

charger to the receiver Nicad battery plug, and AC-plug the

dual charger to AC-outtet socket as shown in the figure.

• The receiver battery can be used about 10 times at 10 min-

utes per flight between rechargings.

• Charge the batteries for about 15 hours. When the set is not

in use for some time, repeat discharge and charge two to

three times before use. (If the batteries are not used for a

long time, their capacity will go down).

• The dual charger transmitter and receiver Nicad batteries

independently or simultaneously.

Notes

1) First connect the charger to the transmitter charge jack.

The LED on the charger will glow RED.

2) Next connect to the receiver switch harness charge cord.

The LED will change to GREENISH-RED (ORANGE).

3) In the case where only one battery pack is connected, the

LED color will be:

TXonly: GREEN

RXonly: RED

Nicad Battery

Connector

Caution

Do not pull the Nicad battery

connector when the back cover

is removed. The power switch

may be damaged if the battery

connector is strongly pulled.

Use a small Phillips

screwdriver

Charger PBC-8B

LED

Charging plug

for transmitter.

AC-plug.

Transmitter

Nicad battery

NT-8JY

Battery cover

NR-4QB

Fig.

Elevator

Aileron

Rudder

The tension of the stick lever spring can be adjusted.

When these screws are

removed, the back cover

can be removed.

•The tension of the

spring can be ad-

justed by removing

the transmitter back

cover and turning

the screw for each

stick. Set the springs

for the best stick feel.

Fig.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba ATTACK_4 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info