Bedienungsanleitung Futaba CGY750 V 2.0 (Seite 11 von 27) (Englisch)

747972

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

WARNING

Verify that the CGY750 compensates in the correct direction before ﬂight. If the compensation

direction is incorrect the model will roll and/or pitch uncontrollably at lift off.

WASH

ASIC

ETTING

SWASH BASIC MAP. 2

(11) Swash ring [default: 130%]

This parameter is used to prevent binding of the swash plate servos when the transmitter control

stick is moved toward a corner (for example, full right and full aft cyclic). Press the Data [+] or [-]

key to adjust the value.

(13) Aileron direction memorizing

This parameter teaches the direction of aileron swashplate movement to the CGY750. Move the

aileron stick to RIGHT full and push the DATA [+] or [-] key. The RIGHT direction of the aileron data

will be saved to CGY750. To conﬁrm the setting, move the aileron stick to full RIGHT, and the “!”

mark will appear on the display. This procedure must be done for the Pirouette and Pitch compen-

sations to function correctly.

(14) Elevator direction memorizing

This parameter teaches the direction of elevator swashplate movement to the CGY750. Move the

elevator stick to full back (pull) and push the DATA [+] or [-] key. The back direction of the elevator

data will be saved to CGY750. To conﬁrm the setting, move the elevator stick to full back, and the “!”

mark will appear on the display. This procedure must be done for the Pirouette and Pitch compen-

sations to function correctly.

(15) Pitch low memorizing [default: 1940μS]

This parameter saves the negative collective pitch point into the CGY750. Move the collective

pitch stick to full negative pitch and push DATA [+] or [-] key. Full negative pitch signal will be saved

to the CGY750. The display shows “!” when the stick is at the saved point. The negative collective

pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or linkage

compensation to function correctly

(9) Swash Rate (rate adjustment) [default: 50% ranges: 0~100%]

The Swash Rate settings are used to adjust the amount of throw-based cyclic pitch is allowed for

roll (aileron) and pitch (elevator). The one setting applies to both roll and pitch axes; they are not

individually adjusted. Use the Data [+] or [-] key to make an adjustment.

(DUAL RATES MUST BE 100)

-Suggested amount of base cyclic pitch

●

800 size – 10 degrees

●

700 size – 9 degrees

●

600 - 550 size – 8 degrees

●

500 size 7 degrees

●

450 and below- 6 degrees

(10) Pitch Rate (rate adjustment) [default: 50% ranges: 0~100%]

The [PIT.Rate] is the amount of collective pitch travel allowed. A good starting range for Sport, 3D

and F3C is +/-10 to +/-12 degrees. Use the Data [+] or [-] key to make an adjustment. 50% ranges:

0~100%

(12) Aileron (roll)/ Elevator (Pitch) Gyro direction setting [default: Normal]

This parameter controls which direction the CGY750 (roll / pitch axis) will compensate when the

helicopter rolls (pitches). Pick the helicopter up and roll the helicopter to the right. The CGY750

should compensate by adding left cyclic to the swash plate. (Pick the helicopter up and rotate

the nose of the helicopter downward. The CGY750 should compensate by adding aft cyclic to the

swash plate.) If the CGY750 compensates in the wrong direction, then it will be necessary to re-

verse the Compensation Direction setting by pressing the [+] or [-] data key once.

Push

MODE

+/– key

Push

DATA

+/– key

Push

DATA

+/– key

Push

DATA

+/– key

(17) Pitch high memorizing [default: 1100μS]

This parameter saves the full positive collective pitch point into the CGY750. Move the collective

pitch stick to full positive pitch and push DATA [+] or [-] key. The full positive pitch signal will be

saved to the CGY750. The display shows “!” when the stick is at the saved point. The positive col-

lective pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or

linkage compensation to function correctly.

(16) Pitch zero memorizing [default: 1520μS]

This parameter saves the zero collective pitch point into the CGY750. Move the collective pitch

stick to zero degrees pitch and push DATA [+] or [-] key. The zero degrees pitch signal will be

saved to the CGY750. The display shows “!” when the stick is at the saved point. The zero degrees

pitch setting must saved into the CGY750 for Pirouette and Pitch compensations and/or linkage

compensation to function correctly.

When CondMenu is ON, this

changes into CondMenu.

When CondMenu is ON, this

changes into CondMenu.

When CondMenu is ON, this

changes into CondMenu.

Rrturn to SWASH BASIC MAP. 1/2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba CGY750 V 2.0 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info