Bedienungsanleitung Futaba CGY750 V 2.0 (Seite 12 von 27) (Englisch)

747972

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

WASH

ETAIL

ETTING

,WHPV±DUHXVHGWRNHHSWKHVZDVKSODWHOHYHODWKLJKDQGORZFROOHFWLYHSLWFKWRF\FOLFLQWHUDFWLRQVDQGF\FOLFSLWFKWRFROOHFWLYHSLWFKLQ-

WHUDFWLRQV7RHQWHUWKHGHWDLOPHQXQDYLJDWHWRWKH%DVLFPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKHPHQXZLOOFKDQJHIURPWKH

%DVLFWR'HWDLO7RH[LWWKH'HWDLOPHQXSUHVVDQGKROGWKHPRGH>@NH\IRURQHVHFRQGDQGWKH%DVLFPHQXZLOOEHGLVSOD\HG

SWASH DETAIL MAP

1/2

(1) Swash expert setting: start display

Use the mode [+] or [-] keys to navigate through the menu.

3,7ĺ$,/PL[LQJUDWH>GHIDXOW@>UDQJHVa@

Going from MID to HIGH and MID to LOW collective pitch check that the swash plate is traveling

ﬂat throughout the entire range. Using the (+/-) Data keys to level the swash plate on the aileron

axis to the middle point by raising or lowing the aileron servo.

3,7ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@

Going from MID to HIGH and MID to LOW collective pitch check that the swash plate is traveling

ﬂat throughout the entire range. Using the (+/-) Data keys to level the swashplate on the elevator

axis to the middle swash position by raising or lowering the elevator servo.

$,/ĺ3,7PL[LQJUDWH>GHIDXOW@>UDQJHVa@

At middle collective pitch check that during right to left and left to right aileron action the swash

plate is staying level on the elevator and collective pitch axis. If the swashplate is rising or falling

with aileron inputs, use the Data (+/-) key to raise or lower the swash plate to match the middle

point during aileron inputs.

$,/ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@

This parameter adjusts the aileron to 2nd elevator mixing rate. The rate can be adjusted for left

and right directions individually. It is only available for H4-45 swash mode.

(/(ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@

This parameter adjusts the elevator to 2nd elevator mixing rate. The rate can be adjusted for up

and down directions individually. It is only available for H4 swash mode.

 (/(ĺ3,7 PL[LQJ UDWH >GHIDXOW + H[FHSW +@ >UDQJHV  a

150%]

During back and forward elevator inputs at middle collective, check if the swash plate is raising or

lowering during the input. If it is moving use the Data (+/-) key to raise or lower the swash plate to

match the middle point during elevator inputs.

 (/(ĺ$,/ PL[LQJ UDWH >GHIDXOW + H[FHSW +@ >UDQJHV  a

150%]

While moving the elevator back and forth at middle collective, check to make sure the aileron axis

is staying level. Use the Data (+/-) key to raise or lower to level the swash plate during full forward

and back elevator input.

(11) Linkage compensation aileron [default: 0%] [ranges: 0% ~ 100%]

At HIGH pitch and LOW pitch check to make sure that the swash plate is staying level on the el-

evator and collective axis when using aileron inputs. If the swashplate is raising or falling, use the

Data (+/-) key to keep the swash plate position the same as middle during aileron inputs.

NOTE – check all four directions: high/right; high/left; low/right; low/left

3,7ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@

This parameter adjusts the pitch to 2nd elevator mixing rate. The rates can both be adjusted indi-

vidually for both full high and low collective positions. It is only available at H4 swash mode.

$,/ĺ(/(PL[LQJUDWH>GHIDXOW@>UDQJHVa@

This parameter adjusts the aileron to elevator mixing rate. The rate can be adjusted for left and

right directions individually. It is only available for H4-45 swash mode.

(12) Compensation direction of the aileron [default: plus]

If the above Data (+/-) correction from 0-100 is NOT in the correct compensation direction, change

the value from PLUS or MINUS using the Data (+/-) key.

Push

DATA

+/– key

Push

MODE

+/– key

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba CGY750 V 2.0 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info