Bedienungsanleitung Futaba CGY750 V 2.0 (Seite 17 von 27) (Englisch)

747972

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

OVERNOR

ASIC

ETTING

OK NG

GOVERNOR BASIC

MAP. 2

(7) Governor on/off switch

[default: Inhibit]

This parameter allows turning of the governor

on and off via a transmitter switch. Pushing the

SET (Data+) key activates the function. The on/

off direction is changed by pushing the SET key

again. The function is inhibited by pushing the

RSET (Data-) key.

(8) Servo limit point setting

Servo limit point setting deﬁnes the overall trav-

el range for the throttle servo. It is fundamental

for governor operation and must be set prior to

other functions. Servo limits must also be reset

when the throttle linkage or trim are changed.

For this setting, idling position is set ﬁrst, then

high position as guided by the display. Push

the data + or – key to memorize. “*Write*” is

displayed when the setting is completed. “Error”

is displayed when the setting position is out of

range (too little servo travel between low and

high throttle positions).

WARNING

When using the CGY750 for the ﬁrst time, or

when making changes in the throw of a servo

and its linkage, always perform the limit setting

operation.

(9) Revolution sensor testing

It tests the output level of the revolution sensor. Turn the engine by hand, and check the output

level. The display indicates the current level on left side numbers, maximum level on right side

numbers. The output level needs to be more than 60 % for correct governor operation.

(10) Sensor type

Select the type of governor sensor:

-Nitro (BPS-1 backplate; Magnet Type)

-1:1 Magnet “1:1 Mag” (Magnet type applied to helicopter part that turns at the same RPM as the

main rotor)

-HPoleEP: For Electric motors 8 poles and above

-LPoleEP: For electric motors 6 poles.

(11) Governor gain

Governor Gain. Too low of number the RPM will ﬂuctuate with collective pitch and cyclic changes.

Too high of gain the RPM will oscillate and possibly surge during ﬂight.

(12) Low limit RPM

Low RPM Limit sets the minimum amount of throttle that the governor will command during an

over-speed situation. Too low of value the engine could shut off or not recover power quickly

enough during the next collective movement. If the value is set too high, the governor will not con-

trol overspeed with the rotor head is unloaded.

Use:

LLmt Lrpm: For RPMS of 700-1700

LLmt Hrpm: For RPMS of 1701-4000

Rrturn to GOVERNOR MAP. 1/2

*It does not display, when Opr.mode is

Gyro+THR, and when SWASH-type is

H4-00/H4-45.

*It does not display, when Opr.

mode is Gyro+THR, and when

SWASH-type is H4-00/H4-45.

Push

DATA

+/– key

Push

DATA

+/– key

Push

MODE

+/– key

Push

DATA

+/– key

When CondMenu is ON, this

changes into CondMenu.

When CondMenu is ON, this

changes into CondMenu.

When CondMenu is ON, this

changes into CondMenu.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba CGY750 V 2.0 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info