Bedienungsanleitung Futaba FP3EG (Seite 9 von 12) (Englisch)

29990

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

•THROTTLE -> RUDDER MIXING

ADJUSTMENT

The rudder neutral position at engine SLOW

and engine HIGH depends on the engine

torque. When adjusted for straight ahead

when a common 2-cycle glow plug engine is

at HIGH, the boat will slowly swerve to the

left at SLOW and if adjusted for straight

ahead when the engine is at SLOW, the boat.

will slowly swerve to the right at HIGH. Mix-

ing from throttle to rudder, the biggest

feature of the Model FP-3EG, completely

eliminates this tendency.

The following description is for a common 2-

cycle glow plug engine that rotates counter-

clockwise. Reverse the description for a gasoline

engine, electric motor, etc. that rotates clock-

wise.

This mixing is adjusted with the mixing

trimmer and limit point trimmer at the left

front of the transmitter.

Mixing trimmer 6 adjusts the amount and

direction of movement of the rudder servo

when the throttle stick is moved up and

down. The mixing amount is zero at the

center position.

Limit point trimmer 7 changes the point at

which the operating line of the mixing

amount to the rudder servo curves when the

throttle stick is moved from LOW to HIGH.

1 When the throttle stick is set to HIGH, a

boat moving straight at engine control

SLOW will swerve to the right. On the

other hand, a boat moving straight ahead

at throttle HIGH will swerve to the left

when the throttle stick is set to SLOW.

That is, the rudder servo should be turned

to the right when the throttle stick is set

to SLOW.

2 Turn the mixing trimmer with a screw-

driver so that the rudder turns slightly to

the right when the throttle stick is moved

from HIGH to SLOW.

You should now have a good understanding

of throttle to rudder mixing.

Throttle -> rudder mixing will be called

"MIX" hereafter.

• Run the boat without MIX (MIX trimmer

at center) and check the rudder neutral,

play, and engine SLOW and HIGH.

• Limit point

Turn the trimmer about

2/3 clockwise.

(In the L to H direction.)

•Under

this

state,

turn the MIX trimmer

about halfway in the R (right) direction

and check the rudder movement (rudder

servo) while moving the throttle stick up

and down. The rudder should move a little

to the right at SLOW and a little to the left

at HIGH.

•Set

the

MIX

trimmer

zero (center) at

throttle stick HIGH. The rudder servo

should not move because the mixing

amount is zero at throttle HIGH as shown

Fig. 11.

4 After all preparations are complete, make

adjustments while actually running.

A Adjust the rudder trimmer so that the

boat travels straight ahead at throttle

HIGH.

B Set the throttle stick to SLOW. If the

boat

swerves

the right

this

time,

the

MIX amount is excessive. Reduce the

MIX amount by turning the MIX trimmer

toward the center. If the boat slowly

swerves to the left, the MIX amount is in-

sufficient. Increase the MIX amount by

turning the MIX trimmer in the R direc-

tion.

C This completes MIX adjustment at throt-

tle SLOW and HIGH. However, adjust-

ment near medium SLOW is still neces-

sary. To adjust near medium SLOW,

proceed as follows:

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP3EG Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info