Bedienungsanleitung Futaba FP3EG (Seite 10 von 12) (Englisch)

29990

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

(a) If the boat slowly swerves to the right

when the throttle stick is set to medi-

um SLOW, the POINT is too high.

Adjust it by turning the limit point

trimmer counterclockwise. Then re-

adjust item B above.

(b) If the boat slowly swerves

to the left,

the POINT is too low. Adjust by turn-

ing the limit point trimmer clockwise.

Then readjust the MIX trimmer as

described in item

(B).

RUDDER DUAL RATE (DUAL-RATE ON,

DUAL-RATE OFF)

•Rudder dual rate switch

Dual-rate (servo stroke becomes narrow) is

effected when this switch is set to ON.

Dual-rate is off when the switch is set to

OFF. OFF is the normal state.

• Rudder dual rate trimmer

This trimmer adjusts the full stroke of the

servo when the rudder dual rate switch is

set to ON. Adjust it to match the course

and technique. The rudder dual rate

amount is continuously variable from 40%

100%.

•The

Futaba

Mini

3-pin

wire servo can

combined with any Futaba transmitter and

receiver. Use it to match the application.

(However, except the Futaba J Module

Series.)

•After mounting and checking are complete,

take your model to the store where you

purchased the digital proportional set, or

to an experienced radio control enthusiast,

and ask them to tell you how to install

your radio control set correctly and to in-

spect your set-up carefully.

Futaba

Digital Proportional Frequencies

Band

(1)

(2)

(3)

(4)

(5)

•

26.995MHz

27.045MHz

27.095MHz

27.145MHz

27.195MHz

72.080MHz

72.160MHz

72.240MHz

72.320MHz

72.400MHz

72.960MHz

75.640MHz

Aircraft use only.

Brown

Red

Orange

Yellow

Green

Brown/White

Blue/White

Red/White

Violet/White

Orange/White

Yellow/White

Green/White

The frequency of Futaba digital pro-

portional sets can be changed among

bands (1)~(5) on the 27MHz band

only.

However, a 27MHz band set cannot be

changed to 72MHz band, and vice

versa.

Therefore, always attach the correct

frequency flag to the end of the

transmitter antenna. Each frequency

band has its own designated color, as

stated above.. The frequency flag is in-

tended for identification purposes.

Also change the frequency flag when

changing the crystal.

Futaba paired crystals are precisely

matched. Always use a Futaba crystal

set (transmitter, receiver) when chang-

ing the frequency.

It is illegal to change crystals of trans-

mitter on the 72-76 MHz bands in the

U.S.A.

FACTORY REPAIR SERVICE

To insure prompt service, please follow the instructions given below.

1. Charge the batteries for at least 18 hours prior to shipment.

2. Return the system only.

Not your complete installation. Remove the servos from their mounts and remove the foam

padding from the receiver.

3. Plugs or other modifications which interfere with factory test procedures will be returned to factory standard at

your expense.

4. Carefully pack all components individually, using sufficient packing material to prevent damage during shipment.

5. Include a brief

but thorough explanation of all problems and service required and tape it to the back of the trans-

mitter. Place a label describing the function of the servo on each servo.

6. Be sure to include your full address and tel. No., zip code in»ide the box as well as on the outside.

7. Include a packing list of all items being returned, and double check to make sure that all items are packed.

8. Upon receipt of your equipment at the Futaba factory, an estimate of the cost of repair (over $25.00 only) will be

sent to you. Your equipment will then be repaired and returned to you upon receipt of payment or C.O.D. (cash).

This factory repair service applies only to the continental U.S.A., Hawaii, and Alaska.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP3EG Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info