Bedienungsanleitung Futaba FP5NLH (Seite 2 von 6) (Englisch)

30012

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

TRANSMITTER FP-T5NLH CONTROLS

Fig. 1 shows the name of each part of the transmitter.

Memorize the position and operation of each

switch and control.

Transmitter crystal

Idle up trimmer

Antenna

Pitch control trimming knob (CH5)

Throttle hold trimmer

Carrying bar

Throttle

hold switch

Revolution mixing down knob

Revolution mixing up knob

Idle up switch

Level meter

Throttle trim

lever

Rudder trim

lever

Throttle

Rudder

Servo reversing

switches

Power

switch

Neck strap bracket

Charging jack

Aileron trim lever

Throttle trim

lever s/ATL

Aileron

Elevator

Nonslip

adjustable lever head

MODE II

Battery cover

Fig.1

Transmitter

NiCad battery

NT-8LP

Aileron AST

trimmer

Elevator AST

trimmer

In the following descriptions, all the servo reversing switches

are assumed to be in the normal position. When they are in the

reverse position, operation is the opposite of that described.

Mixing circuit is used for cancelling the torque reaction of the main

rotor. The controls for set the minimum mixing necessary for heli-

copter flight.

Aileron Aileron operation

Elevator Elevator operation

Throttle Throttle operation

Rudder Rudder operation

Pitch control trimming knob (CH5)

Pitch control trimming knob. Approximately 30% of the full throw

of the servo can be adjusted and set. Normally, it is set for the best

pitch during flight.

Aileron trim lever Aileron trimmer.

Elevator trim lever Elevator trimmer.

Throttle trim lever w/ATL

Adjustable throttle limiter

type

trim

lever.

Operates

a trim lever only when the

throttle stick is at the

SLOW side as shown in

Fig.

SLOW

Servo throw by

throttle trimmer

As the HIGH side does not

change even when the trim

is altered, it is extremely

convenient when connect-

ing the linkage, etc.

(30% of full throw;

Throttle servo

Rudder trim lever Rudder trimmer.

Revolution mixing down side ratchet

knob

(down

side

knob)

Revolution mixing up side ratchet knob (up side knob)

• Knob which adjusts the throttle rudder mixing amount. Approxi-

mately 70% mixing

the up and

down

sides.

Exclusively

for

rotor

clockwise rotation.

The LOW side mixing amount from mid throttle (hovering point)

position is adjusted and set with the down side knob

The HIGH side mixing amount from mid throttle (hovering point)

position is adjusted and set with the up side knob

• The amount of the

revolution mixing

up side knob 11

and down side

knob 10 begins

individually set

from the neutral

position of the

HIGH

Fig. 2

Servo throw

by throttle

stick

throttle stick

Mixing is adjusted and

set over this range with

the revolution mixing

up side knob 11 .

.Throttle stick neutral

position

Mixing is adjusted and

set over this range with

the revolution mixing

down

side

knob®.

Throttle hold switch

When this switch is ON, the throttle servo stops at the position set

with trimmer and only the pitch servo is controlled toy the

throttle stick. It is used for auto rotation landings. When this, switch

is OFF, the throttle and pitch servos are mixed. The switch is turn-

ed on when pulled forward.

Throttle hold trimmer

Trimmer which

sets

the

throttle

servo stop

position

when the

throt-

tle hold switch is ON. Full travel setting is possible.

Idle up switch

When this switch is pulled forward, it is turned on and the position

set with the idle up trimmer on the back of the transmitter

becomes the maximum slow position of the throttle servo. When

this switch is set to OFF, the normal slow position of the stick be-

comes the maximum slow position of the throttle servo.

Power switch The upper position is ON.

Level meter This level meter indicates the transmitter battery voltage

Neck strap bracket Bracket for the neck strap (optional).

Antenna

Strong telescoping antenna. Extend it to its full length when using

the transmitter.

Handle Use this bar to carry the transmitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP5NLH Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info