Bedienungsanleitung Futaba FP5NLH (Seite 4 von 6) (Englisch)

30012

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

RECEIVER FP-R107N & SERVO FP-S130

Receiver, servos, switches, and battery connections

Receiver crystal

4 servos are provided

as standard.

Aileron servo

Elevator servo

Throttle servo

Rudder servo

7-channel FM receiver FP-R107N

Antenna wire

SSW-J

Power switch

Charging

Plug

Gyro output

switching

connector is not

connected.

Gyro output

polarity switch

Control

amp

C Connector Red

NR-4J

Connector servo (rudder servo for helicopter)

neutral trimmer. (This trimmer is effective even

when the control box power switch is set toOFF.)

The parts enclosed

by the dotted lines

must be purchased

separately.

Pitch control

servo

Fig.

Pay careful attention to the

connector polarity.

Five battery

pack 6V con-

nector for motor

regulated power

supply. (When

the power supply

is used in com-

mon with the

receiver, insert

the jumper

connector.)

Jumper connector

Gyro output trimmer

Control box

Gyro

Rate gyro FP-G152

PRECAUTIONS

• Connect the receiver, servos, switches, and battery firmly as shown in

Pig.11. Then extend the transmitter and receiver antennas fully.

• Set the transmitter power switch to ON. Then set the receiver power

switch to ON. The servos stop near the neutral position. Operate the

transmitter sticks and check that each servo follows the movement of

the stick.

• Connect the pushrod to each servo horn, then check if the direction

of travel of each servo matches the direction of operation of its trans-

mitter stick. To reverse the direction of servo travel, switch the servo

reversing switch.

• Operate each servo over its full stroke, and check if the pushrod binds

too

loose.

Applying

unreasonable force

the

servo

horn

will

adversely affect the servo and quickly drain the battery. Always make

the travel of each control mechanism somewhat larger than the full

travel (including trim) of the servo horn. Adjust the servo horns so

that they move smoothly even when the trim lever and stick are

operated simultaneously in the same direction.

• Be alert for noise.

This set is noise-resistant, but is not completely immune to noise. We

recommend the use of noiseless parts.

• When installing the switch harness, cut a rectangular hole somewhat

larger than the full stroke of the switch and install the switch so that

it moves smoothly from ON to OFF. This also applies to the switch

mount when the switch is installed inside the fuselage and is turned

on and off from the outside with a piece of wire, etc. Install the

switch where it will not be exposed to engine oil, dust, etc.

• Even though the receiver antenna is long, do not cut or bundle it.

•

Install the

servos

securely.

Tighten the

mounting

screws

until

the

rubber

grommet

crushed slightly.

the

screws are

too

tight,

the

cushioning effect will be adversely affected.

• The crystal can be changed from the outside of the receiver case.

Always use the Futaba transmitter/receiver matched crystal set to

change the band.

• Spare servo horns are supplied. Use them as needed.

• Wrap the receiver in sponge rubber. Waterproof and dustproof the

receiver by placing it in a plastic bag and wrapping a rubber band

around the open end of the bag. Do the same with the receiver/servo

battery.

• Use the rubber bands wrapped around the receiver to hold the servo

and switch leads.

• After mounting is complete, recheck each part, then check the range

by making the transmitter antenna as short as possible, extending the

receiver antenna fully, and operating the set from a distance of 20m

to 30m. The movement of each servo should follow the movement of

each stick of the transmitter.

• After mounting and checking are complete, take your model to the

shop where you purchased the set, or to an experienced radio control

modeler, and ask them to teach you how to handle your radio control

set in the proper manner and to inspect your set-up carefully.

• To enjoy radio control models fully, be sure to observe all safety

standards.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP5NLH Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info