Bedienungsanleitung Futaba FP5NLK (Seite 5 von 6) (Englisch)

30018

Zoom out

Zoom in

Vorherige Seite

1/6

Nächste Seite

• Even though the receiver antenna is long, do not cut or

bundle it.

• Install the servos securely. Tighten the mounting screws

until the rubber grommet is crushed slightly. If the screws

are too tight, the cushioning effect will be adversely affect-

ed.

• Wrap the receiver in sponge rubber. Waterproof and dust-

proof the receiver by placing it in a plastic bag and wrapping

a rubber band around the open end of the bag. Do the same

with the receiver/servo battery. .

• Use the rubber bands wrapped around the receiver to hold

the servo and switch leads.

• After mounting is complete, recheck each part, then check

the range by making the transmitter antenna as short as

possible, extending the receiver antenna fully, and operating

the set from a distance of 20m to 30m. The movement of

each

servo

should

the

movement

each stick

the

transmitter.

• After mounting and checking are complete, take your model

to the shop where you purchased the set, or to an experienc-

ed radio control modeler, and ask them to teach you how to

handle your radio control set in the proper manner and to

inspect your set-up carefully.

•To enjoy radio control models fully, be sure to observe all

safety standards.

AILERON AND ELEVATOR DUAL (dual rate ON,

OFF) ADJUSTMENT

When the dual switch is set to ON, the servo throw is made

smaller by the amount shown by the hatched lines in Fig. 10.

The servo throw can be set from 40% to 100% of the total

travel by adjusting the trimmer next to the switch with a flat

bladed screwdriver. When the dual rate switch is set to OFF,

the

throw

normal. When

desiring

larger

throw,

such

for

spins, etc., set the dual rate switch to OFF and adjust the

throw mechanically by horn and rod adjustment. Set the

dual

rate

switch

to on for

level

flight and adjust the

trimmer

for the required amount of throw.

When the dual rate switch is set to OFF, dual rate is set and

the throw becomes large.

Fig.

This horn permits shifting of the

servo neutral position at the servo

horn. Setting and shifting the

neutral position

a) Angle divisions

b) Effect

Fig.

Fig. 13

1) The splined horn has 25 seg-

ments. The amount of change per

segment is; 360: 25=14.4°

2) The minimum adjustable angle

is determined by the number of

arms or number of the holes. For

four arms, the minimum adjustable

angle is:

To shift the holes center line to

the right (clockwise) relative to

baseline A, shift arm 2 to the po-

sition of arm 1 and set it to the

position closest to baseline A.

(Example] For a four arm horn,

the angular shift per segment

14.4°. The shift to the right is

90°

(14.4

x6)

3.6°

To shift by the same angle in the

opposite direction, use the oppo-

site arm number.

Fig.

Arm 3 shift 4.8° to the right, arm

6 shifts 2.4° to the left,and arm 4

shifts 7.2° to the right and left.

For a six arm horn, turn the arm

counterclockwise and set arm 2

to the position of arm 1. The ad-

justable angle is 60° - (14.4 x 4)

=2.4°.

Fig.

The following splined horns are optional.

Fig.

Baseline A

HORN A HORN B HORN C HORN D BORN B HORN P

USING THE ANTENNA FREQUENCY FLAG

Insert the frequency flag into

the flag holder as shown here.

The flag can be attached to, and removed

from, the end of the transmitter antenna

with one touch.

Fig. 17

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP5NLK Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info