Bedienungsanleitung Futaba FP8SSAP (Seite 9 von 44) (Englisch)

30094

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

22 Monitor Lamps

IMPORTANT: In all instructions on control functions. Items designated by a number inside a circle

(For example 10 ) are transmitter controls normally accessable and operated in flight.

Items designated by a number within a box (For example 10 ) are adjustment functions not operated

while in flight.

Lamp A Power Monitor

• When the power switch

23 is set to ON, this lamp flashes on

briefly and then goes out momentarily as the Fail Safe data is auto-

matically matically transmitted to the receiver. Fail Safe data is

transmitted every 60 seconds at which time the lamp also goes out

momentarily. If the transmitter Nicd battery nears full discharge,

this lamp starts blinking, indicating that the power error backup

function is activated. When this occurs, transmitter memory func-

tion settings are lost and must be reset.

Lamp

3 -> 6. 7 -> 2 I 3 -> 8 Mix

This lamp comes on when Safety Switch 7 and/or [33] is set to

ACT position, indicating that throttle —-> flap, spoiler —-> elevator

mixing and/or throttle -> pitch control mixing functions are activat-

ed. This lamp will blink when transmitter control switch II is set

to ON (placing these functions in operation).

Lamp C 6, 7 -> 2 Mix

• This lamp comes on when Safety Switch [32] is set to ON (flap,

spoiler -> elevator mix) or CH7 OFF (flap -> elevator mix) position.

This lamp blinks when transmitter control switch 10 is set to ON.

Lamp D Snap Roll

Fig.1

• When Safety Switch [29] is set to ACT (snap roll function acti-

vated), this lamp blinks. When the Snap Roll switch 13 is pulled,

this lamp continues blinking.

When the power switch 23 is set to ON, lamp (A) will go out momentarily. This indicates automatic data

transmission on and is not a failure.

23 Power switch

• The transmitter power ON-OFF switch is pro-

vided with a locking feature to prevent acciden-

tal movement. To operate the switch, pull the

knob gently outwards and set to the desired

position (UP=ON. DOWN=OFF).

25 Level meter

• This meter indicates the transmitter battery

voltage and output power.

•When the antenna 26 is extended fully and

the power switch 23 is set to ON, the pointer

should move to the white zone.

•If the transmitter RF Module

32 is not

in-

stalled, the meter pointer will not move.

• If the meter pointer moves to the red zone,

indicating that the Nicd battery voltage is low,

the

signal

range

will

become

shorter.

the

Tachometer/timer 21 power switch is ON, the

battery alarm function will operate after about

one more flight. When the meter pointer stops

at the boundary between the white and red

zones, recharge the battery.

26 Antenna

Strong 1m 10cm telescoping antenna. Extend

the antenna to its full height when using the

transmitter. The antenna will lock in place with

a click when pulled up to its full height.

27 Carrying handle

28 Tachometer sensor connector

•When not using this connector and the charg-

ing socket 29, cover them with the rubber-

backed cover supplied to protect them against

dust.

29 Charging socket and DSC (Direct Servo Con-

troller) connector

• This connector is used as both the charging

socket and DSC connector. See

page 10 for

charging instructions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSAP Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info