Bedienungsanleitung Futaba FP8SSHP (Seite 8 von 36) (Englisch)

30098

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

22 Hovering throttle ratcheted knob

•Trims the throttle servo independently from the

pitch control servo (without regard to mixing).

Since

the throttle

servo

can

trimmed

without

interfering with other mixing, this knob is very

convenient when trimming the throttle while

hovering.

• When the throttle lever

[3]

is at about the center,

the throttle servo throw can be adjusted about

25% of the total travel with this knob.

•When the throttle lever

[3]

is at the low

or high

sides, the throttle servo does not operate even if

this knob is turned.

24 Monitor lamps

Lamp ®

Fig.

Lamp B Lamp C Lamp D

Throttle servo

total travel

Adjustable within this

range with knob 22 .

Throttle servo

Fig.

23 Throttle hold switch (TH switch)

Right ON, Left OFF.

•This switch is used during auto-rotation. If this

switch is set to ON when the throttle lever [3] is

in the maximum slow position, the throttle servo

will stop at the position (idling or engine stop)

set at trimmer

[8]

on the trimmer panel at the

back of the transmitter. At this time, the time set

at trimmer

[7]

(throttle hold delay) is applied and

the pitch control servo is set to the optimum

pitch for auto-rotation set with trimmer

[5].

This

setting can be made without regard to the posi-

tion

of the

pitch

control

high

side

trimmer

lever

[13 ]

•When fail safe switch [12] on the trimmer panel

the back of the transmitter is set to the INH posi-

tion, the throttle hold function is inoperative.

When it is set to the T.HOLD position, monitor

lamp [D] comes on to indicate that the throttle

hold function is set.

If the TH switch [23] is then set to ON, lamp [D]

goes out to indicate that throttle hold is being

performed.

Lamp

When the power switch [30] is set to ON, this lamps

comes on and the pointer of the level meter de-

flects. At FS data transmission, this lamp goes out

momentarily and data transmission can be moni-

tored. The lamp goes out once every 60 seconds.

When the internal Nicd battery approaches full

discharched, this lamp starts blinking. This alarm

indicates that the power error backup function is

activitated the memory and circuit (memory, ATV,

FS, etc.) is not functioning.

Lamp

When fail safe switch [13] on the trimmer panel at

the back of the transmitter is to the IDLE 1 posi-

tion (idle up 1 function ON), this lamp lights.

When the idle up 1 switch [19] is set to ON, this

lamp goes out.

Lamp

When

fail safe switch

[14]

on the trimmer panel at

the back of the transmitter is set to the IDLE 2

position (idle up 2 function ON), this lamp comes

on. When the idle up 2 switch [21] is set to ON,

this lamp goes out.

Lamp

When fail safe switch [12] on the trimmer panel at

the back of the transmitter is set to the T.HOLD

position (throttle hold function ON), this lamp

comes on. When the throttle hold switch [23] is set

ON, this lamp goes out.

When the power switch [30] is set to ON, lamp [[A]

will go out momentarily. This indicates automatic

data transmission on and is not a failure.

Functions priority

Lamp B (Idle up 1 )

Lamp C (Idle up 2 )

Lamp D (Throttle hold)

The function priority is hold -> idle up 2 -> idle

up 1 . Lamps B, C, and D come on when the

pertinent fail safe switch (13, 14, 12) is set to the

ON position. When the idle up 1 switch [19] is set

to ON, lamp

[B]

goes out. Keeping the idle 1

switch [19] in the ON position, try setting the idle

up 2 switch [21] to ON. Lamp B comes on and

lamp [C] goes out, indicating that the idle up 2

function has priority. Similarly, if the throttle

hold switch [23] is set to on while the 1 switch

[19]

and 2 switch

[21]

are ON, lamps B and C go out,

indicating that the throttle hold function has

priority.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSHP Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info