Bedienungsanleitung Futaba FX22 (Seite 44 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

1. Model addition and selection

Initially, the FX-22 assigns the first model to

model-01 in the transmitter. To add new models

or to select a model already programmed, use the

Model Select function of the Linkage Menu.

This is convenient when selecting a model after

entering the model's names in advance. The FX-

22 is capable of storing up to 30 models in the

transmitter's internal memory. Additional models

can also be stored in an optional SD card.

The currently selected model is displayed in

the middle of the screen. Before flying and before

changing any settings, always confirm the model

name.

When a new model is added, the Model Type select

screen and system mode setup screen automatically

appear. Change, or check that they match the swash

type and receiver type of the model used.

When a new model is added, you will need to re-

link the receiver.

2. Model type and swash type selection

If a different model type is already selected,

select helicopter with the Model Type function of

the Linkage Menu, and then select the swash type

matched to the helicopter.

*The Model Type function automatically selects the

appropriate output channels, control functions, and mixing

Helicopter basic setting procedure

This section outlines examples of use of the helicopter functions of the FX-22. Adjust the actual values,

etc. to match the fuselage used.

functions for the chosen model type. Six swash types are

available for helicopters.

*For a description of the swash type selection, refer to the

MODEL TYPE function.

3. Flight condition addition

7KHWUDQVPLWWHURIIHUVXSWR¿YHÀLJKWFRnditions

per model.

The Condition Select function automatically

DOORFDWHV¿YHFRQGLWLRQVIRUKHOLFRSWHUV

(Initial setting)

ŏ NORMAL

ŏ IDLE UP1 (SW-E)

ŏ IDLE UP2 (SW-E)

ŏ IDLE UP3 (SW-F)

ŏHOLD (Hold switch is not assigned initially)

Note: Since you may accidentally activate

a condition that not previously setup during

ÁLJKWZKLFKFRXOGFDXVHDFUDVKZHVXJJHVW

deleting conditions that are not used.

*For a description of the condition deletion, refer to the

Condition Select function.

The NORMAL condition is always on, and

remains on until other conditions are activated by

switches.

The priority is throttle hold/idle up 3/idle up 2/

idle up 1/normal. Throttle hold has the highest

priority.

The Condition Delay can be programmed for

each channel and condition. The Condition Delay

is used to change the servo throw smoothly when

switching conditions.

*HQHUDOÀLJKWFRQGLWLRQVHWWLQJH[DPSOH

ŏ Normal: (Use initial setting conditions/operate

when switch OFF)

Use from engine starting to hovering.

ŏ Idle up 1: (Operate at SW-E center)

Use in stall turn, loop, and other maneuvers.

ŏ Idle up 2: (Operate at SW-E forward side)

Use in rolls.

ŏ Throttle hold: (Operate at SW-G forward side)

Use in auto rotation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info