Bedienungsanleitung Futaba FX22 (Seite 46 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

function from the Model Menu, and set the curve

for each condition. (At initial setting, this function

is in the "INH" state. To use it, set it to the "ON"

state.)

6HWWLQJH[DPSOH!

Activate the mixing curve of each condition with

the condition select switch.

A curve setting example is shown below.

ŏPitch to RUD mixing curve (Normal)

Use the hovering system and set this curve to

match take off and landing and vertical climb at a

constant speed.

ŏPitch to RUD mixing (Idle up 1)

Use this curve in stall turn, loop, and adjust it so the

fuselage is facing straight ahead when heading

into the wind.

ŏPitch to RUD mixing (Hold)

This function is set so that the fuselage is facing

straight ahead at straight line auto rotation. The

pitch of the tail rotor becomes nearly 0

9. Throttle hold setting

*If throttle hold is necessary, please refer to the THR HOLD

function.

10. Throttle cut setting

Throttle cut provides an easy way to stop the

HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFN

at idle. The action is not functional at high throttle

to avoid accidental dead sticks. The switch’s

location and direction must be chosen, as it defaults

to NULL.

*With throttle stick at idle, adjust the cut position until the

engine consistently shuts off, but throttle linkage is not

binding.

6ZDVK0L[FRUUHFWVDLOHURQHOHYDWRUDQG

pitch interaction

The swash mix function is used to correct the

swash plate in the aileron (Left/Right Cyclic)

and elevator (Forward/Aft Cyclic) direction

corresponding to each operation of each condition.

6. D/R function

D/R function is used to adjust the throw and

operation curve of aileron, elevator and rudder for

each condition.

*For throttle and pitch curve settings, refer to the afore-

mentioned "Throttle/Pitch curve setting"

7KLVLVQRUPDOO\XVHGDIWHU(QG3RLQWKDVGH¿QHG

the maximum throw directions.

*\URVHQVLWLYLW\DQGPRGHVZLWFKLQJ

The gyro sensitivity and mode switching

function is utilized to adjust the gyro mixing of the

model, and can be set for each condition.

ŏ Normal condition (hovering): Gyro sensitivity

maximum

ŏ Idle up 1/Idle up 2/Throttle hold: Gyro

sensitivity minimum

ŏ However, during auto rotations with a tail-

driven helicopter, this function may not have

any effect on the high gyro sensitivity.

3LWFKWR58'PL[LQJVHWWLQJ

Note: When using a Futaba GY Gyro, or other

heading hold gyro, this Pitch to RUD mixing

should not be used. The reaction torque is

corrected by the gyro. When operating the

gyro in the AVCS mode, the mixed signal will

cause neutral deviation symptoms and the

gyro will not operate normally.

Use this function when you want to suppress

the torque generated by the changes in the pitch

and speed of the main rotor during pitch operation.

Adjust it so that the nose does not swing in the

rudder direction. However, when using a heading

hold gyro like those shown above, do not use Pitch

to rudder mixing.

Activate the Pitch to rudder (Pit

→

RUD) mixing

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info