Bedienungsanleitung Futaba FX22 (Seite 67 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

MODEL SELECT

The Model Selection function performs model addition, selection,

deletion, copy, and model name setting.

This function is used to load the settings of the

desired model into the FX-22’s memory.

The settings may be selected from either the

transmitter’s internal memory or an SD card.

Remember that up to 30 model memories are available

in the transmitter.

The name of the model stored in the transmitter and

the SD card may be changed. This can be very useful

to tell different models settings apart. Each model name

can be as long as 10 characters, and the model name

always appears in the display screen.

The Copy function is used to copy parameters,

settings, etc. from one model data into a second

memory. It may be used for getting a head-start on

setting up models with almost the same settings (only

GLIIHUHQFHVQHHGWREHPRGL¿HGLQVWHDGRIHQWHULQJWKH

complete model from scratch). Also, this function may

be used to make a backup copy of a model setup before

any changes are made.

*FX-22 can use the model data of FX-20 for SD card,

copying it. However, the model data of FX-22 cannot be

used by FX-20.

Model selection

*Model data saved on the transmitter memory other than the

model currently used can be selected.

1. Move the cursor to the save destination

display ("TX" or "CARD") and touch the RTN

button to switch to the data input mode.

Select the save destination by scrolling the

touch sensor and touch the RTN button.

[TX]: Transmitter memory

[CARD]: SD card

2. After moving the cursor to the desired model

in the model list, touch the RTN button.

3. Move to [SELECT].

4.Touch the RTN button. A confirmation

message is displayed. Touch the RTN button

for one second and selection is complete.

*Transmission stops and then starts in the new model.

Model addition

*A new model can be added to the transmitter memory. It can

not be added to the SD card.

1. Move the cursor to [NEW].

2. Touch the RTN button. A confirmation

message appears. Touch the RTN button for

one second.

*The model type setup screen and frequency setup screen are

DXWRPDWLFDOO\GLVSOD\HG&RQ¿UPRUFKDQJHWKHPRGHOW\SH

and SYSTEM mode.

*Transmission stops and then starts in the new model.

*The added model appears in the model list of the model

select setup screen.

*Link is required when a new model is

made from a model selection.

ŏ Select [MODEL SELECT] in the Linkage menu

and access the setup screen shown below by

touching the RTN button.

*The display screen is an example. The

screen depends on the model type.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

(Model list)

Current model

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info