Bedienungsanleitung Futaba FX22 (Seite 143 von 174) (Englisch)

747921

143

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

143

ŏ Select the function name

and return to the Model

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

MOTOR

[Corresponding model type]: Airplane/glider, general

This function lets you set the speed when the

motor of an F5B or other EP glider is started via

a switch. The operation speed can be set for two

ranges, slow speed flight and high speed flight

(Speed 1/Speed 2). This function can also be

operated as a safety function by programming it to

a switch.

ŏ The In side and Out side operating speeds can

be adjusted independently in 2 ranges (Speed 1/

Speed 2).

ŏ The boundary between the 2 ranges can be set.

(From Speed 1 to Speed 2)

ŏ The operational speed can only be activated at

the initial operation. However, operation can be

repeated by setting the switch to OFF before the

operation is Ànished. When you want to reset one

time operation, set the ACT/INH item to [INH] and

then reset it to [ON].

ŏ The motor channel is controlled by SW-G. (Glider:

Initial setting) When changing the switch or stick

which controls the motor, Àrst change Function of

the Linkage menu.

ŏ If the Model Type selected is Airplane, the MOTOR

function is changed from INH to ON and it is not

assigned to another channel, the changes from

the throttle channel to the motor channel are

enabled.

Note: Initial setting does not assign a motor

channel according to the model type. Prior to

DVVLJQLQJWKHPRWRUFKDQQHOÀQGDQXQXVHG

channel. Then, use the Function menu of the

Linkage menu.

Set [Control] to the switch you want to use

and [Trim] to [--].

Note: When using this function, always check

the initial operation with the propeller

removed.

ŏ Select [MOTOR] at the Model menu

and access the setup screen shown

below by touching the RTN button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Setting method

Ɣ$FWLYDWHWKHIXQFWLRQ

When using this function, move the cursor to

the [ACT/INH] item and touch the RTN button

to switch to the data input mode. Select the

[ACT] by scrolling the touch sensor and touch

the RTN button.

When selecting the ON/OFF switch, move the

cursor to the switch item and touch the RTN

button to access the selection screen. Select

the switch and set its ON direction. (Always

ON at "--" setting)

*For a description of the switch selection method, see the

description at the back of this manual.

Ɣ0RWRURIISRVLWLRQVHWWLQJ

Move the cursor to the [MOTOR OFF] item

and touch the RTN button for one second

when the motor function switch (SG, etc.) is

in the motor OFF position you want to set. The

direction of the motor switch is memorized.

The screen graph display OFF direction also

changes.

Note:

ŏ)LUVWGHFLGHWKHPRWRU2))GLUHFWLRQDQGWKHQ

set the speed. When you want to reset the

motor OFF direction, also reset the speed.

ŏ:HUHFRPPHQGWKDW0RWRU2))EHVHWLQ

combination with F/S.

ŏ6HWWKHEDVLF RSHUDWLRQGLUHFWLRQZLWKWKH

Reverse function to match the ESC used.

ŏ$OZD\VVHWWKH0RWRU2))SRVLWLRQ

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 143

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info