Bedienungsanleitung Futaba FX22 (Seite 145 von 174) (Englisch)

747921

145

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

145

ŏ Select the function name

and return to the Model

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

RUD to ELE

[Corresponding model type]: Airplane, general

This function is used when you want to mix

elevator operation with rudder operation. It is used

to correct undesirable tendencies when rudder is

applied in rolling maneuvers such as, knife edge

ÀLJKW

ŏ Mixing during flight can be turned ON/OFF by

setting a switch. (Always ON at [--] setting)

ŏ Link mixing can be set: Links this mix to other mixes.

ŏ Select [RUD to ELE] at the Model

menu and access the setup screen

shown below by touching the RTN

button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Setting method

Ɣ$FWLYDWHWKHIXQFWLRQ

Move the cursor to the [ACT] item and touch

the RTN button to switch to the data input

mode. Select the ACT mode by scrolling the

touch sensor.

*The display blinks.

Touch the RTN button to activate the

function and return to the cursor mode. (ON

is displayed.)

When selecting a switch, move the cursor to

the [SW] item and touch the RTN button to

call the selection screen. Select the switch

and set its ON direction. (Always ON at "--"

setting)

*For a description of the switch selection method, see the

description at the back of this manual.

ƔSRLQWFXUYHVHWWLQJDLUSODQH

[Curve rate setting]

1. Move the cursor to the curve rate setting

item (left side) you want to adjust and touch

the RTN button to switch to the data input

mode.

Adjust the rate by scrolling the touch sensor.

Adjustment range: -100~100

*When the RTN button is touched for one second, the rate is

reset to the initial value.)

Touch the RTN button to end the adjustment

and return to the cursor mode.

2. Repeat this procedure for each point.

[Moving curve point]

1. Move the cursor to the curve point setting

item you want to adjust and touch the RTN

button to switch to the data input mode.

Adjust the curve point by scrolling the touch

sensor.

Adjustment range: Up to 2.5 in front of the

adjoining point

*When the RTN button is touched for one second, the curve

position is reset to the initial value.)

Touch the RTN button to end the adjustment

and return to the cursor mode.

2. Repeat this procedure for each point.

[Deleting/returning curve point]

Move the cursor to the curve point setting

item you want to delete/return and touch

the RTN button for one second.

Ɣ/LQNPRGHVHWWLQJ

When selecting the link mixing, move the

cursor to the [LINK] item and touch the RTN

button to switch to the data input mode.

Select the ON mode by scrolling the touch

sensor.

*The display blinks.

Touch the RTN button to set the link mode

and return to the cursor mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 145

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info