Bedienungsanleitung Futaba T10 CAG (Seite 17 von 119) (Englisch)

450995

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

Changing Modes (

TX SETTING

Hold down MODE and END keys while turning on the transmitter to enter the

TX SETTING

menu.

Stick Mode: The screen reads "

STK-MODE

". Use the DIAL to change this to the correct mode.

Note that this will NOT change the throttle and elevator rachets, etc. Those are mechanical

changes that must be done by a service center.

Throttle Reverse:

THR-REV

is a special function that reverses the entire throttle control, including moving the trim

functionality to the stick’s upper half. To use

THR-REV

, CURSOR DOWN to

THR-REV

and turn the DIAL to

REV

. Turn the

transmitter off and back on. This change affects all models in the radio. (

GLID

only): The separate

THR-REV

settings for each

model can be set. (See p.33)

Display language: can be selected the display language of the function name, etc. in each function menu. The screen reads

LANGUAGE

". Change this to the desired language.

Area Selection (Frequency Range):

The T10CG transmitter has been designed to function in many countries. If you will be utilizing this transmitter in a

country other than France, please make sure that

TM10-MODE

is set to "

GENERAL

". If, however, this transmitter will be

utilized in France, it must be set to "

FRANCE

Power Down mode (

TM10 POWER MODE

We have installed a special "Power Down Mode" for doing a ground range check. Hold down

DIAL while turning on the transmitter to call

TM10 POWER MODE

menu.

Power Down Mode: To activate the "Power Down Mode" press DIAL and the home screen will appear. During this mode,

the RF power is reduced so the range test can be performed. In addition, when this mode is activated the blue LED on the

front of the transmitter starts blinking and the transmitter gives users a warning with a beep sound every 3 seconds.

The "Power Down Mode" continues for 90 seconds and after that the power will return to the normal level. To exit the

"Power Down Mode" before the 90 seconds, press DIAL again. This mode is available one time only so if you need to re-

use this function the transmitter power must be cycled and the "Power Down Mode" reset. NEVERVWDUWÀ\LQJZKHQWKH

"Power Down Mode" is active.

Power Off Mode: To use the RF power off mode, CURSOR DOWN to

OFF

and press DIAL. During this mode, the RF

power is turned off. The blue LED on the front of the transmitter is turned off.

CAMPac Initializing Method and Data Conversion (T9C/T9CS to T10CG):

Insertion of a new CAMPac or a CAMPac containing data of a different transmitter type will

open

EXT-MEMORY

menu after turning the transmitter on.

To initialize the CAMPac, CURSOR DOWN to "Yes" and press DIAL and the check display of "OK?" will appear. Press

DIAL again, the initializing of the CAMPac will start.

7RFRQYHUWWKH&$03DFGDWDIURP7&7&6WR7&*VHOHFWWR1RE\CURSOR lever and then press DIAL and the

home screen will appear. See p.30 for the conversion method.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T10 CAG Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info