Bedienungsanleitung Futaba T10 CAG (Seite 18 von 119) (Englisch)

450995

Zoom out

Zoom in

Vorherige Seite

1/119

Nächste Seite

RADIO INSTALLATION

Follow these guidelines to properly mount the servos, receiver and battery.

• Make certain the alignment tab on the battery, switch and servo connectors is oriented correctly and “keys” into the

corresponding notch in the receiver or connectors before plugging them in. When unplugging connectors, never pull on

the wires. Always pull on the plastic connector instead.

• If your aileron servo (or others) are too far away to plug into the receiver, use an aileron extension cord to extend the

length of the servo lead. Additional Futaba extension cords of varying lengths are available from your hobby dealer.

Always use an extension of the proper length. Avoid plugging multiple extensions together to attain your desired length.

If distance is greater than 18” or multiple or high current draw servos are being used, use Futaba Heavy-Duty servo

extensions.

Servo

Rubber

grommet

Servo

Rubber

grommet

• Always mount the servos with the supplied rubber grommets. Do not over

tighten the screws. No part of the servo casing should contact the mounting

UDLOVVHUYRWUD\RUDQ\RWKHUSDUWRIWKHDLUSODQHKHOLFRSWHUVWUXFWXUH2WKHUZLVH

YLEUDWLRQZLOOEHWUDQVPLWWHGWRWKHVHUYRFDXVLQJSUHPDWXUHZHDUDQGRUVHUYR

failure.

• Note the small numbers (1, 2, 3, 4) molded into each arm on the Futaba 4-arm servo arms. The numbers

indicate how many degrees each arm is “off” from 90 degrees to correct for minute manufacturing

deviations from servo to servo.

• To center the servos, connect them to the receiver and turn on the transmitter

and receiver. Center the trims on the transmitter, then find the arm that will be

perpendicular to the pushrod when placed on the servo.

• After the servos are installed, operate each servo over its full travel and check that the pushrods and servo arms do not

bind or contact each other. Also make sure the controls do not require excess force to operate. If there is an objectionable

buzzing sound coming from a servo, there is probably too much resistance in the control. Find and correct the problem.

Even if there is no servo damage, excess battery drain will result.

• Use the mounting plateIURPWKHUHFHLYHURQRIIVZLWFKDVDWHPSODWHIRUWKHFXWRXWDQGVFUHZKROHV0RXQWWKHVZLWFK

on the side of the fuselage opposite the engine exhaust, and where it won’t be inadvertently turned on or off during

handling or storage. Be certain the switch moves without restriction and “snaps” from ON to OFF, and that the cutout

allows full motion of the switch in both directions.

• When you install the switch harness to the helicopter, please use the switch cover. Generally sandwich the frame between

the switch and switch cover and securely tighten the screws. Different models might require different installations. If so,

please follow the model's instruction manual.

Fasten about 5-10cm

from the servo outlet

so that the lead wire

is neat.

Slack in the lead wire.

• To prevent the servo lead wires from being broken by vibration during

ÀLJKWSURYLGHDVOLJKWDPRXQWRIVODFNRUH[WUDVRWKDWWKHZLUHVWLFNVRXW

slightly and fasten it at suitable points. In addition, periodically check the

wire during daily maintenance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T10 CAG Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info