Bedienungsanleitung Futaba T14-MZ (Seite 43 von 127) (Englisch)

520093

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

●Throttle curve (Idle up 2)

This is the idle up amount which can maintain

rotation even when the pitch was pulled out by

setting the throttle to the slow side.

●Setting at hold condition

Note: A curve itself cannot be used at the hold

condition, but the throttle curve idle point becomes

the idle point standard of the Throttle Hold function.

Conﬁ

rm that the rate of the slowest position (0%) of

the stick is 0% (initial setting).

Be sure that when set to high side 100%, the curve

of any condition does not exceed 100%.

A pitch curve setting example is shown below.

Call the pitch curve of each condition with the

condition select switch.

*Pitch curve graph display can be switched to pitch angle

direct reading display.

●Pitch curve (Normal)

Make the pitch at hovering approximately +5

Set the pitch at hovering with the stick position at

the 50% point as the standard.

*Stability

at hovering may be connected to the throttle curve.

Adjustment is easy by using the hovering throttle function

and hovering pitch function together.

●Pitch curve (Idle up 1)

The idle up 1 pitch curve function creates a curve

matched to airborne ﬂight.

Set to -7

~+12

as standard.

●Pitch curve (Idle up 2)

The high side pitch setting is less than idle up 1. The

standard is +8

●Pitch curve (Hold)

At auto rotation, use the maximum pitch at both

the high and low sides.

[Pitch angle setting example]

Throttle hold: -7

~+12

6. Throttle hold setting

Call the Throttle Hold function from the Model

Menu and switch to the throttle hold condition with

the condition select switch.

Note: At initial setting, the setting mode is the

group mode. Since this function is not used at other

onditions, switch to the single mode before setting.

●Setting to the state which activates the

function

The throttle hold function allows setting for throttle

cut and switching of the function ﬁxed at the idle

position by switch for training. Either one or both

functions can be performed.

●Hold position setting

This function sets the servo operation position at

throttle hold. (Throttle cut and idle positions)

●Other settings

When you want to link operation with stick

manipulation, the Auto mode can be set.

When you want to adjust the servo speed, adjust

[Speed].

7. Pitch to RUD mixing setting

Pitch to RUD mixing suppresses the reaction

torque of the main rotor, and can be set by curve

for each condition. However, when using a high

performance gyro like those shown below, do not

use Pitch to RUD mixing.

Note: When using a GY601, GY502, GY401, or other

high-performance gyro, this Pitch to RUD mixing

does not have to be used. The reaction torque is

corrected at the gyro side. When operating the

gyro in the AVCS mode, the mixed signal will cause

neutral deviation symptoms and the gyro will not

operate normally.

Call the Pitch to RUD mixing function from the

Model Menu, and set the curve for each condition.

(At initial setting, this function is in the "INH"

state. To use it, set it to the "ON" state.)

(17 points curve)

Curve setting of up to 17 points is possible.

However, in the following setting example, a

simple curve can be adjusted by using the [Linear]

curve type.

Note: At initial setting, the setting mode is the group

mode. In this mode, the same contents are set at

all the added curves. When you want to set the

selected condition only, switch to the single mode.

Call the mixing curve of each condition with the

condition select switch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T14-MZ Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba T14-MZ

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info