Bedienungsanleitung Gaggenau CI292102 (Seite 51 von 60) (Englisch)

761566

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

en Cookware check

Cookware check

This function can be used to check the speed and

quality of the cooking process depending on the

cookware.

The result is a reference value and depends on the

properties of the cookware and the hotplate being used.

1With the cookware still cold, fill it with approx.

200 ml of water and place it on the centre of the

hotplate with the diameter that most closely

matches that of the base of the cookware.

2Go to the basic settings and select the ™ˆ setting.

3Touch the control panel. A will flash on the hotplate

display.

The function has now been activated.

After 10 seconds, the result for the quality and speed of

the cooking process will appear in the hotplate display.

Check the result using the following table:

To reactivate the function, turn the twist knob.

Notes

– The flexible cooking zone only counts as a single

cooking zone; place no more than one item of

cookware on it.

– If the diameter of the cooking zone that is used is

much smaller than the diameter of the cookware,

only the middle of the cookware can be expected to

heat up. This may result in the cooking results not

being as good as expected or not being

satisfactory.

– You can find information on this function in the

section entitled ~ "Basic settings".

– You can find information on the type, size and

positioning of the cookware in the sections entitled

~ "Induction cooking" and ~ "Flex function".

Result

‹The cookware is not suitable for the hotplate and will

therefore not heat up.*

‚The cookware is taking longer to heat up than expected

and the cooking process is not going as well as it

should.*

ƒThe cookware is heating up correctly and the cooking

process is going well.

* If there is a smaller hotplate available, test the cookware

again on the smaller hotplate.

Y| [|

Power manager en

Power manager

You can use the power manager to set the total power of

the hob.

The hob is preset at the factory. Its maximum

performance is specified on the rating plate. You can

use the power manager to change the value in

accordance with the requirements for the relevant

electrical installation.

In order not to exceed this set value, the hob

automatically distributes the power available between

the cooking zones that are switched on.

As long as the power manager function is activated, the

output of a cooking zone may temporarily fall below the

nominal value. If a cooking zone is switched on and the

power limit is reached, ¬ appears in the heat setting

display for a short time. The appliance automatically

regulates and selects the highest possible power level.

For more information about how the total power of the

hob is changed, see section ~ "Basic settings"

Cleaning

Suitable maintenance and cleaning products can be

purchased from the after-sales service or in our e-Shop.

Hob

Cleaning

Always clean the hob after cooking. This will prevent

food deposits from becoming burned on. Only clean the

hob after the residual heat indicator has gone out.

Clean the hob with a damp dish cloth and dry it with a

cloth or towel to prevent limescale build-up.

Only use cleaning agents that are suitable for this type

of hob. Observe the manufacturer's instructions on the

product packaging.

Never use:

▯Undiluted washing-up liquid

▯Cleaning agents designed for dishwashers

▯Abrasive cleaners

▯Harsh cleaning agents, such as oven spray and

limescale remover

▯Scouring pads

▯High-pressure cleaners or steam jet cleaners

Stubborn dirt is best removed with a glass scraper,

available from retailers. Observe the manufacturer's

instructions.

You can obtain a suitable glass scraper from customer

services or through our online shop.

Using a special sponge for cleaning glass-ceramic hobs

achieves a great cleaning result.

Note: Do not use any cleaning agents while the hob is

still hot. This may mark the surface. Make sure that any

residue left by cleaning agents is removed.

Potential marks

Limescale and

water marks

Clean the hob as soon as it has cooled

down. You can use a cleaning agent suit-

able for glass-ceramic hobs.*

Sugar, rice starch

or plastic

Clean immediately. Use a glass scraper.

Caution: Risk of burns.*

* Then clean with a damp dish cloth and dry with a cloth or

towel.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gaggenau CI292102 Seite 51

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gaggenau CI292102

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info