762099
30
Zoom out
Zoom in
Vorherige Seite
1/34
Nächste Seite
30
Installation and connection
Delivery
Your dishwasher has been checked thoroughly in the
factory to ensure that it is in working order. This may
cause small water stains. These will disappear after
the first wash cycle.
Technical specifications
Weight:
max. 45 kg
Voltage:
220–240 V, 50 Hz or 60 Hz
Connected load:
2000–2400 W
Fuse:
10/16 A (UK 13A)
Power input:
off mode (Po)* 0.10 W
left on mode (Pl)* 0.10 W
*according to regulations (EU) nos. 1016/2010 and
1059/2010
Additional functions and settings may increase the
power input.
Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar).
At a higher water pressure: connect pressure-
reducing valve ahead.
Inlet rate:
minimum 10 litres/minute
Water temperature:
cold water; hot water max. temperature 60 °C.
Capacity:
9–10 place settings (depending on model).
Installation
The required installation dimensions can be found in
the installation instructions. Level the appliance with
the aid of the height-adjustable feet. Ensure that the
appliance is situated securely on the floor.
A built-under or integrated appliance which is
installed subsequently as a free-standing
appliance must be secured to prevent it from
overturning, e.g. by screwing it to the wall or by
installing it under a continuous worktop which is
screwed to adjacent cupboards.
The appliance can easily be installed in a fitted
kitchen between wooden and plastic walls.
Waste-water connection
1The required work sequence can be found in the
installation instructions. If required, fit a siphon
with an drainage connection.
2Connect the waste-water hose to the drainage
connection of the siphon with the enclosed parts.
Ensure that the drainage hose is not kinked,
crushed or twisted and that there is no cover plate
in the drainage to prevent the waste water from
flowing out!
Drinking water connection
1Fasten the drinking water connection to the tap
according to the installation instructions using
the enclosed parts.
Ensure that the drinking water connection is not
kinked, crushed or twisted.
2When replacing the appliance, always use a new
water supply hose.
Water pressure:
At least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar).
At a higher water pressure: connect pressure-
reducing valve ahead.
Inlet rate:
Minimum 10 litres/minute
Water temperature:
Cold water preferred; hot water max. temperature
60 °C.
30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gaggenau DF250141 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info