Bedienungsanleitung Gardena CSI 4020-X-8863 (Seite 16 von 21) (Englisch)

474442

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

D. ASSEMBLY / DISASSEMBLY

BAR AND CHAIN ASSEMBLY

Take great care when assembling to ensure this is performed correctly.

ENGLISH - 6

E. START-UP AND STOPPING

Start-up: grip both handles firmly, release the chain

brake lever whilst ensuring hand is still on front

handle, press and maintain the switch block (fig E1)

pressed in, then press the switch (fig E2) (at this

point the switch block can be released).

Stopping: The machine will stop whenever the

switch is released or by activating the chain brake.

F. BAR AND CHAIN LUBRICATION

ATTENTION! Insufficient lubrication will provoke

chain breaking and can cause serious injury.

Refer to “Maintenance & Storage” for indications on

ensuring that the chain oil is sufficiently distributed.

Choice of chain oil

Use oil which is approved by the manufacturer.

We advise the use of bio chain oil which is

biologically degradable.

Filling oil tank

Unscrew the oil tank cap, and fill the tank taking

care not to spill any oil (if this occurs clean the

machine carefully) and then screw the cap back on

tightly.

Remove the plug from the power supply before working on the product.

1a & 1b. Check that the chain brake is not activated. If so, deactivate it.

2a & 2b. Unscrew the chain tensioning knob and rotate in an anti-clockwise direction to remove the drive

sprocket cover.

Wear Gloves.

3 Position the chain over the bar, starting at the nose sprocket, fitting it into the guide bar groove.

Ensure that the sharp side of the cutting teeth face in a forward direction on the upper part of the bar.(see

markings on the bar)

4. Rotate the chain tensioning mechanism anti-clockwise as far as possible.

5a & 5b. Mount the bar on the bar retaining screw and it will attach to the magnet. Position the chain over

the drive sprocket.

6a & 6b. Replace the drive sprocket cover, ensuring the drive teeth of the chain are engaged in the drive

sprocket and in the bar guide groove.

7a & b. To tension the chain, turn the chain tensioner knob in a clockwise direction until securely tightened.

The chain is now tensioned correctly for use.

Tensioning the chain too tightly will overload the motor and cause damage. Insufficient tension can provoke

chain derailing, whereas a chain tightened correctly provides the best cutting characteristics and prolonged

work life. Check the tension regularly because the chain length tends to stretch with use (especially when

the chain is new; after the first assembly, the chain tension must be checked after a few minutes machine

operation); in any case do not tighten the chain immediately after use, but wait until it cools down.

In cases where the loosened chain needs to be adjusted, always unscrew the chain tensioning knob 2 turns

and then securely tighten again leaving the chain tensioned for use.

Warning:- The chain and guide bar can become very hot

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardena CSI 4020-X-8863 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Gardena CSI 4020-X-8863

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info