Bedienungsanleitung Gardenline DM53E3-D196 (Seite 18 von 24) (Englisch)

724643

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

196cc 4 Stroke Petrol Lawn Mower

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL No.: DM53E3-D196 • 08/2018 • 56979

(toll free)

AFTER SALES SUPPORT

(toll free)

196cc 4 Stroke Petrol Lawn Mower

e-mail: help@powertoolsupport.com1800 909 909

MODEL No.: DM53E3-D196 • 08/2018 • 56979

32 33

Maintenance Maintenance

Replacing the Blades

NOTE. Before making any adjustment or

maintenance procedures to the lawn mower ensure

it is turned o and the spark plug lead is removed.

NOTE. Wear heavy gloves to protect your hands.

1. With the engine switched o, remove the hard

catcher (43) and lift the front of the lawn mower

upwards so the upper handle bar (1) sits on the

ground and the spark plug faces upwards.

2. Remove the blade bolt (31) using a 17mm spanner (not supplied) by

turning in an anti-clockwise direction (Fig AK), then remove the outer

ange and washer (32) (Fig AL). This allows you to be able to remove the

blade mounting plate (37) from the lawn mower.

3. To remove a single blade from the blade mounting plate (37), again use

a 17mm spanner (not supplied) to loosen and remove the nut, screw and

washers. (Fig AM/AN)

NOTE: There is 1 washer located under the screw

on the outer side of the blade mounting plate (37),

and one on the underside of the blade mounting

plate in between the blade and blade mounting

plate (37). Be careful not to lose these (Fig AO).

AN.AM.AL.

AO.

AK.

Maintenance

4. Repeat the process to remove the other 3 blades.

5. Clean the dirt and grass from around the blade mounting area.

6. Replace all 4 blades to ensure a smooth even cut and re-t them on the

mower in the reverse direction they were removed.

7. Lastly, secure the nuts rmly, (20-25Nm) repeating this for the other

3 blades.

8. Replace the blade mounting plate (37) with new blades attached, then

the outer ange (32), followed by the blade bolt (31). Retighten the blade

bolt tightly (50 – 59Nm).

NOTE: Use a wooden block to stop the blade from turning. The 4 blades

should be tightened fully but check to ensure they can still swing back

if they were to hit a solid object. Where required tighten the bolts with a

torque wrench, the centre disc blade bolt torque: 50 – 59Nm and the four

blades torque: 20-25Nm. If you do not have a torque wrench ask a mower

service dealer to tighten the blade bolts before you use the mower.

Blades should be replaced when they become worn and no longer cut

the grass cleanly. The performance of grass catching can also reduce if the

blades become worn. Replacement blade sets are available for purchase

from https://help.tools/ or by calling 1800 909 909.

Removing Oil

IMPORTANT: Drain the oil while the engine in still warm to ensure rapid and

complete draining.

1. With the engine o but still warm, disconnect the spark plug cover and

make sure it is kept away from the spark plug (27).

2. Remove the oil drain plug (36) bolt (Fig AP), using a 10mm spanner (not

supplied) in an anti-clockwise direction to loosen (Fig AQ).

WARNING:

Oil may be hot.

AQ .AP .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline DM53E3-D196 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info