Bedienungsanleitung Gardenline EB-500-E (Seite 9 von 19) (Englisch)

724623

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. EB-500-E • 03/2019 • 60099

(toll free)

AFTER SALES SUPPORT

(toll free)

51.7cc 2 Stroke Petrol Backpack Blower

e-mail: info.aldi@positecgroup.com1300 889 028

MODEL: №. EB-500-E • 03/2019 • 60099

14 15

Preparation of the Blower prior to use

This petrol Backpack blower requires some assembly prior to use.

This includes joining of the blower tubes (13,14,15,16), and securing the

adjustable throttle control handle with ﬁtting clamp (7) to the upper blow

tube (14).

Setting up for use

WARNING. Blower tube installation affects both blower balance

and performance.

Stop the engine before installing or removing the blower tubes. Never

perform any maintenance or assembly procedures on this machine while

the engine is running.

Assembling the Upper Blow Tube (14)

1. Place the blower in an upright position on the ground or on a sturdy

work surface (Fig A).

2. Loosen the 2 x adjustable clamps on the ﬂexible pipe (13) using the

screwdriver end of the supplied spark plug spanner / combination

screwdriver (28) by turning the screw on the clamp in an anti-clockwise

direction until they are loose on each end of the ﬂexible pipe (13) (Fig B).

3. Push the larger opening end of the ﬂexible pipe (13) over the end of the

elbow tube (12) approximately 3cm until it hits the last raised ridge on

the end of the elbow tube (12) (Fig C).

4. Secure the adjustable clamp on the ﬂexible

pipe (13) using the screwdriver end of the

supplied spark plug spanner / combination

screwdriver (28) by turning the screw on the

clamp in a clockwise direction until tight

(Fig D).

5. Before proceeding to add the other tubes

for assembly, the adjustable throttle control

handle with ﬁtting clamp (7) needs to be

assembled onto the upper blow tube (14).

Assembling the Adjustable Throttle

Control Handle to the Upper Blow

Tube (14)

1. Loosen the wing nut on the adjustable throttle

control handle with ﬁtting clamp (7) by

turning in an anti-clockwise direction (Fig E).

2. Align the locking pins on the end of the upper

blow tube (14) with the 2 channels on the

adjustable throttle control handle with ﬁtting

clamp (7) then insert the upper blow tube

(14) through the back side of the ﬁtting clamp

(where the cable is located) through to the

front of the ﬁtting clamp (Fig F).

3. With the adjustable throttle control handle

with ﬁtting clamp (7) now ﬁtted loosely to the

upper blow tube (14), you can now position

it to best ﬁt the user. The ﬁtting clamp can be

rotated to the left and right to suit the users

requirement, or can be locked into position by

pushing it further up on the tube to engage

the notch on the top of the ﬁtting clamp with

the raised channel on the upper blow tube

(14) (Fig G).

C.A. B.

TIGHTEN

LOOSEN

Assembly

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline EB-500-E Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info