Bedienungsanleitung Gardenline EB-500-E (Seite 10 von 19) (Englisch)

724623

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

51.7cc 2 Stroke Petrol Backpack Blower

AFTER SALES SUPPORT

e-mail: info.aldi@positecgroup.com

1300 889 028

MODEL: №. EB-500-E • 03/2019 • 60099

(toll free)

AFTER SALES SUPPORT

(toll free)

51.7cc 2 Stroke Petrol Backpack Blower

e-mail: info.aldi@positecgroup.com1300 889 028

MODEL: №. EB-500-E • 03/2019 • 60099

16 17

4. Secure the ﬁtting clamp into position by

tightening the wing nut on the ﬁtting clamp in

a clockwise direction (Fig H).

NOTE: the adjustable throttle control handle

with ﬁtting clamp (7) can be re-adjusted after

full assembly of the other tubes.

Assembling the Middle & Lower

Blow Tubes (15/16)

1. With the adjustable throttle control handle

with ﬁtting clamp (7) now secured to the

upper blow tube (14), insert the end of the

upper blow tube (14) with raised ridges on

it inside the ﬂexible pipe (13), approximately

4cm until it can not be pushed in any further

(Fig I).

2. Secure the other adjustable clamp on the

ﬂexible pipe (13) using the screwdriver end of

the supplied spark plug spanner / combination

screwdriver (28) by turning the screw on the

clamp in a clockwise direction until tight (Fig J).

3. To add the middle blow tube (15), ﬁrstly loosen

the assembly screw by turning it in an anti-

clockwise direction using the screwdriver

end of the supplied spark plug spanner /

combination screwdriver (28) until the screw

end is sitting ﬂush on the internal side of the

middle blow tube.

4. Align the 2 raised locking pins on each side of

the end of the upper blow tube (14) with the

2 x channels on the middle blow tube (15).

Before pushing the 2 tubes together, ensure

the assembly screw is on the underside of the

middle blow tube otherwise the assembly

screw will not engage with the hole in the

upper blow tube (Fig K). Push the tubes

together, and then rotate in a clockwise

direction to connect the tubes together.

You will feel the tubes engage if done correctly.

5. Tighten the assembly screw using the

screwdriver end of the supplied spark plug

spanner / combination screwdriver (28) in a

clockwise direction until tight (Fig L).

6. To add the lower blow tube (16), ﬁrstly loosen

the assembly screw by turning it in an anti-

clockwise direction using the screwdriver

end of the supplied spark plug spanner /

combination screwdriver (28) until the screw

end is sitting ﬂush on the internal side of the

lower blow tube (16) (Fig M).

7. Align the 2 raised locking pins on each side

of the end of the middle blow tube (15) with

the 2 x channels on the lower blow tube (16).

Before pushing the 2 tubes together, ensure

the assembly screw is on the underside of the

lower blow tube (16) otherwise the assembly

screw will not engage with the hole in the

middle blow tube (Fig N). Push the tubes

together, and then rotate in a clockwise

direction to connect the tubes together.

You will feel the tubes engage if done

correctly.

8. Tighten the assembly screw using the

screwdriver end of the supplied spark plug

spanner / combination screwdriver (28) in a

clockwise direction until tight (Fig O).

H. L.

I. M.

J. N.

K. O.

TIGHTEN

LOOSEN

TIGHTEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline EB-500-E Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info