Bedienungsanleitung Gardenline FCS4800A (Seite 9 von 20) (Englisch)

724644

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

47.1cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 61705 • 08/2018 • FCS4800A

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

47.1cc Petrol Chainsaw

MODEL: №. 61705 • 08/2018 • FCS4800A

14 15

7. Once the chain (20) is in position around the

nose of the guide bar (19), ensure that the chain

links are located within the bar guide channel,

(Fig G), and the chain (20) is fully located around

the drive sprocket (29).

8. On the chain drive side cover (23), adjust the

chain tensioning screw (37) in an anti clockwise

direction as per the following, so the assembly

of the guide bar (19) is NOT tight on the chain

(20). When replacing the existing chain, rotate

the adjustment screw 5 FULL turns in an anti-

clockwise direction.

When replacing with a new chain, rotate the

adjustment screw 10 FULL turns in an anti-

clockwise direction (Fig H).

9. After adjusting the chain tensioning screw

(37), replace the chain side cover (23) on to the

chainsaw and hold the cover rmly against the

Bar. DO NOT t the nuts (Fig I). While holding

the cover on rmly, grasp the guide bar (19) and

slide it outward slowly (Fig J).

When the chain tensioning pin (30) aligns with

the clearance hole in the bar, the cover will drop

rmly and at on the bar (Fig L - shows internal

side on chain drive side cover and where the

chain tensioning pin is located).

If the chain tensioning pin (30) does not align,

adjust the chain tensioning screw (37) using the

combination tool (at blade screwdriver) (32) so

the pin aligns with the hole in the bar (Fig K).

The chain tensioning pin (30) must enter the guide bar (19), and the at

faces of both the chainsaw and chain drive side cover (23) must be at

against the bar before the nuts are applied.

10. Fit the chain drive side cover nuts (24) and tighten FINGER TIGHT (Fig M).

Check again the cover is at on the surface of the bar.

11. Rotate the chain (20) a few times to ensure the chain (20) is free to rotate

around the drive sprocket (29) and is correctly engaged on the sprocket.

12. Check the tension of the chain (20). It will need to be tightened. Tighten

the chain tensioner screw (37), in a clockwise direction (previous Fig K)

until the links of the chain just touch the bottom edge of the guide

bar (19).

The chain should be fully seated in the bar channel. DO NOT over tighten.

The chain (20) should be able to be lifted at least 5mm in the centre of the

bar (Fig N).

13. Tighten the chain drive side cover nuts (24) rmly using the supplied

combination tool (bar nut tube spanner) (32) (Fig O).

CAUTION: A new chain (20) will stretch after just a few minutes of use.

Check and, if necessary, re-adjust the chain tensioning screw (37).

A loose chain causes rapid wear to both the chain (20) and the guide bar

(19) and could derail causing a major safety hazard.

NOTE: Do not make ANY adjustments with the chainsaw engine running.

14. To tighten a loose chain (20), loosen the chain drive side cover lock nuts

(24), then using the supplied combination tool (at blade screwdriver)

(32), turn the chain tensioning screw (37) clockwise to tighten the chain

(20) (Fig H). Do not over tighten, the chain (20) should be able to lift 5mm

from the middle of the bar.

15. Retighten the chain drive side cover nuts (24) rmly using the supplied

combination tool (at blade screwdriver) (32) (Fig O). Run the chainsaw

for approximately 30 seconds and then turn the chainsaw o. Retest the

chain.

Assembly Assembly

K.L.

O.M.

TIGHTEN

5MM

5 FULL

TURNS

ANTICLOCKWISE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline FCS4800A Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info