Bedienungsanleitung Gardenline FCS4800A (Seite 11 von 20) (Englisch)

724644

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

47.1cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 61705 • 08/2018 • FCS4800A

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

47.1cc Petrol Chainsaw

MODEL: №. 61705 • 08/2018 • FCS4800A

18 19

5. Secure fuel tank cap (9) nger tight, and then using the oil tank cap (7),

secure the fuel tank cap (9). ENSURE you wipe any residue from around the

fuel tank cap (9).

6. It is important to now ll the combination oil tank (6) with 4 stroke engine

oil per following instructions.

NOTE: Should you lose the oil tank cap (7), an additional oil tank cap (7) has

been supplied with this chainsaw

Adding 4 Stroke Oil to the Chainsaw

WARNING: Always ensure the engine is turned o before

undertaking this task.

WARNING: Never start work unless the chain (20) and guide bar (19)

are lubricated.

NOTE TO CHECK: Always ensure the combination oil tank (6) is full of 4 stroke

engine oil each time the chainsaw is being used.

1. Using a funnel, ll the oil tank (6) with 260ml of quality 4 stroke oil, or to just

under the lip of the oil tank opening. (Fig S).

2. Fasten the combination oil tank cap (7), and if there is any spillages, ensure

you clean with a clean rag.

Preparation Operation

Operation

WARNING: Do not start the engine whilst the chainsaw hangs from one

hand. This is very dangerous as the chain (20) may come in contact with your

body and the starting action is not controlled .

NOTE: This chainsaw is tted with an easy start recoil starter (11).

This means the recoil starter only needs to be pulled at a steady medium rate

and not hard vigorous pulling.

1. Fill the fuel and oil tanks respectively per

previous instructions and ensure both caps are

secure. Remove the bar cover (31).

2. Press in the priming bulb (5) up to 10 times, or

until the priming bulb (5) is rm and full of fuel,

when the chainsaw is cold or being used for the

rst time, or after the chainsaw has previously

run out of fuel (Fig T).

4. Press the on/o switch (4) to the “On” position, as marked with an “I” (Fig

U). For safety when starting, make sure the front guard / chain brake (13) is

on by pushing it rmly towards the nose of the chainsaw bar until a click is

heard (Fig V).

5. When the machine is cold, or the chainsaw has previously run out of fuel,

pull out the choke control (10) to the fully extended position (Fig W).

6. Hold the chainsaw securely on the ground by

placing one foot on the rear handle, one hand

securing the front handle. Using your other

hand, pull at a steady and medium rate on the

recoil starter (11) (Fig X).

7. Repeat until the engine res, and then STOP as

soon as the engine kicks (attempts to start) or

runs in any way.

8. Push the choke control (10) back in (Fig Y).

9. Pull the recoil starter (11) again and restart the

engine. Allow the engine to warm up.

10. When ready to start cutting, release the front

guard / chain brake (13), by pulling it rmly

towards the back of the chainsaw until a click is

heard (Fig A).

U. V. W.

FULLY

EXTEND

X 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline FCS4800A Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info