Bedienungsanleitung Gardenline FCS4800A (Seite 13 von 20) (Englisch)

724644

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

47.1cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 61705 • 08/2018 • FCS4800A

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

47.1cc Petrol Chainsaw

MODEL: №. 61705 • 08/2018 • FCS4800A

22 23

Checking the operation of the clutch.

Each time the chainsaw is started, the operation of the clutch (22) should

be checked as per the following detail. The chain MUST rst be checked to

ensure correct tension adjustment before starting.

1. When attempting to start the chainsaw, the chain (20) should not be trying

to move around the guide bar (19) under the inuence of the recoil starter

(11). If it is trying to rotate around the guide bar (19), STOP the starting

process and take the saw to an authorised service centre.

2. If point 1 is correct and the chain (20) is not trying to rotate around the

guide bar (19), start the chainsaw as per the section in the manual “Starting

the Chainsaw”.

3. With the chainsaw operating and at idle and ensuring the chain (20) is in

a safe position with respect of other persons and any objects, release the

chain brake (13).

CHECK, the chain (20) should NOT be rotating around the guide bar (19) at

idle speed.

4. Operate the safety lever (2) and then accelerate the throttle trigger (3).

The chain (20) should start and rotate. The harder the throttle trigger (3)

is pulled, the faster the chain (20) will rotate. RELEASE the throttle trigger

(3) so the motor returns to the idle condition. The chain (20) MUST stop

rotating around the guide bar (19) when the motor of the saw is at idle.

5. If the chain (20) is constantly rotating when the motor of the saw is at idle,

the chainsaw should NOT be used and the chainsaw should be taken to an

authorised service centre for repair.

6. DO NOT use the chainsaw if the clutch (22) does not totally disengage

when the motor of the saw is at idle.

Re-setting the Chain Brake

The front guard / chain brake (13) operates automatically in the event of

kickback. In the event of a kickback, the guide bar (19) kicks up, the wrist of

the operator’s hand on the top handle knocks against the front guard / chain

brake (13) causing it to move forward thus activating the chain brake (13).

To reset the front guard / chain brake (13) this can be done manually by

pulling it rmly towards the back of the chainsaw until a click is heard. (Fig A).

CAUTION: Each time the chainsaw is used, check that the chain brake (13)

is operating correctly.

Operation

WARNINGS:

• Always follow the safety instructions given at the front of this manual.

This chainsaw must only be used for cutting wood. It must not be used

for cutting other types of material. Do not use the chainsaw as a lever for

lifting, moving or splitting objects.

• Do not attach the chainsaw to a xed stand.

• Do not attach any devices to the chainsaw other than those specied by

the manufacturer.

• Be aware of any local or national restrictions when using this appliance.

This could include, but is not restricted to, times of operation, location of

operation, or work place operation.

Helpful Hints

• Do not force the chainsaw into the cut. Apply only light pressure whilst

running the engine at full throttle.

• If the chain (20) gets caught in the cut, do not try to remove it by twisting

the guide or pulling forcibly. Use a lever or wedge to open up the cut so

that the chain is freed.

Vibration

Vibration white nger may occur in operators using hand held vibrating tools

such as chainsaws. Continual vibration can cause both vascular damage and

also Nerve Damage to the operator.

The following guidelines can reduce the risk:

- Limit the use of vibrating tools.

- Hold vibrating tools as loosely as possible and in varying positions.

- Ensure tools are well maintained; make sure cutting blades are kept sharp

to maintain eciency, and replace worn parts.

- Use tools correctly, and use the right tool for the job (to do the job more

quickly and reduce exposure time).

- Store tools so that they do not have very cold handles when next used.

- Use anti-vibration gloves.

- Take regular breaks of at least 10 minutes every hour away from the tool.

Operation Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline FCS4800A Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info