Bedienungsanleitung Gardenline FCS4800A (Seite 12 von 20) (Englisch)

724644

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

47.1cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 61705 • 08/2018 • FCS4800A

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

47.1cc Petrol Chainsaw

MODEL: №. 61705 • 08/2018 • FCS4800A

20 21

Using the Chainsaw

1. Once the engine is started, and the front guard

/ chain brake (13) is released (Fig A), press in the

safety lever (2), and then the throttle trigger (3)

(Fig Z), and the chain will start operating. To

engage full speed of the chain, pull the throttle

trigger (3) inwards fully.

2. To stop the chain operating, release the throttle

trigger (3), and the safety lever (2) (Fig AA).

Stopping the Chainsaw

1. Press down the on/o switch (4) to the “O”

position as indicated by an “O” (Fig AB).

NOTE: Especially after the rst starting of the

chainsaw, the tension of the chain should be

checked. The chain will become loose on the

rst start up and will require adjustment. Refer

to the “Changing / Replacing the Guide Bar and

Chain” section.

Checking the Oil supply

Run the engine at medium speed and check that

the chain splatters a thin line of oil which can be

seen on the ground when the guide bar (19) is

pointed downwards (Fig AC). DO NOT ALLOW THE

TIP OF THE BAR touch ANY surface when checking

the oil ow. Keep the chain (20) and guide bar (19)

well clear of ANY surface. This visual thin line of

oil is normal and is an indication the oil system is

oiling the guide bar (19) and chain (20).

NOTE: For rst time use the oil may take a few

minutes to work through the oil system.

The oil pump is ONLY operating while the chain

(20) is rotating so at idle the oil is NOT being

pumped through the oil system. If there is no line

of chain oil after a few minutes, stop the engine

immediately and investigate the cause.

The oil tank (6) could be empty or the oil supply to

the chain blocked. This may require removal of the

guide bar (19) and checking that the upper oil hole

in the bar is clear of any blockages (Fig AD).

AC.

AA.

AB.

AD.

Quick adjustment of the Carburetor

NOTE: Out of the box the chainsaw is already

pre-set and calibrated to one turn out from fully

turned in. However if the product is running

poorly the carburetor can be adjusted manually to

provide the best performance.

Poor running can be caused by stale fuel or

changes in climate, very dry climates, or wet

climates can create the need for some changes.

NOTE: It is preferred the above operation is

performed by a service centre to ensure the correct

setting for both safety and performance.

The carburettor is factory set and should not

require adjustment.

Changes in operating conditions may require ne

tuning of the carburettor. To reset or calibrate your

carburetor, proceed as follows:

H = HIGH (Fast) run adjustment screw (26). (Fig AE)

L = LOW (Slow) run adjustment screw (27). (Fig AF)

T = Idling adjusting screw (25). (Fig AG)

1. Stop the engine and screw in both the H

and L screws (26 and 27) using the supplied

screwdriver (33). Do not force.

2. Turn the H screw (26) back 1 turn.

3. Turn the L screw (27) back 1 turn.

4. To nd the correct idling speed, start the engine

and let it warm up with the throttle trigger (3)

half pulled in. When the engine is warm, release

the throttle trigger (3).

5. Turn the L screw (27) slowly clockwise until the

idling speed is at its maximum then turn the

screw back (anticlockwise) 1/4 of a turn.

6. Turn the “T” idling adjusting screw (25)

anticlockwise until the chain does not turn.

7. If the idling speed is too slow, turn the “T” idling

adjusting screw (25) clockwise.

8. Make a test cut and adjust the H screw (26) for

best cutting power, not for maximum speed.

9. If after the above you may slightly adjust the

turns and nd the most appropriate setting.

AE.

AF.

AG.

HIGH

LOW

IDLING

Operation Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline FCS4800A Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info