Bedienungsanleitung Gardenline FCS4800A (Seite 17 von 20) (Englisch)

724644

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

47.1cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 61705 • 08/2018 • FCS4800A

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

47.1cc Petrol Chainsaw

MODEL: №. 61705 • 08/2018 • FCS4800A

30 31

WARNING: The chain has sharp edges.

Use work gloves for safety.

Vents:

1 . Clean any dust away from the cooling vents as

clogged vents can cause overheating.

Servicing

• It is recommended once you rst use your product to get it serviced after

15 hours of use.

• From thereafter, service the product every 2 years, or every 50 hours of

use if frequently used.

• A 3mm hex key (36) is supplied for the purpose of future maintenance /

servicing.

Always t the chain and bar cover (31) when the chainsaw is not in use.

It is recommended to drain BOTH fuel and oil from the chainsaw on the

completion of use, prior to storage or transportation.

Always sit the chainsaw on a surface where the leakage of oil will not be

a problem. The chainsaw is tted with an oil pump and there will be after

use an amount of oil in the oil channels inside the chainsaw, and also in the

chain and bar channel. This oil can spill on to the surface the chainsaw is

sitting as it drains from the above points.

Always store the chainsaw in an area safe away from the elements of the

environments, i.e. high humidity, wet locations, hot environments etc.

Storage area should also be out of reach of children of both the chainsaw

and all accessories.

Store the chainsaw ensuring the bar cover securely covers the chain (20)

and guide bar (19). The chainsaw should always be stored with the On/O

switch (4) in the ‘O’ position and the chain brake (13) ON.

If the chainsaw is to be stored for a long period of time it is advisable to

apply a thin spray of oil over the chain (20), guide bar (19) and all exposed

metal parts.

The chainsaw should be thoroughly cleaned of all wood chips, dirt etc prior

to storage. A chainsaw carry bag (38) is supplied with this chainsaw.

Place the chainsaw with the bar cover (31) installed, into the chainsaw bag,

and secure the zip. Carry it safely using either the shoulder strap or by

securing the velcro carry handle.

AU.

Air Filter:

1. Remove the air lter cover (15) by rotating the

air lter knob (16) in an anti-clockwise direction,

and removing the air lter cover (15) (Fig AM).

2. Disconnect the black pipe from the cylinder

cover (Fig AQ), and then also from the air lter

itself.

3. Grasp the sides of the air lter (14) and pull it

outwards (Fig AR).

4. Dry particles can be removed by tapping on a

hard surface. More stubborn dirt may require

washing the air lter (14) with warm soapy

water and a soft brush.

5. After thoroughly drying the air lter (14),

re-install the black pipe onto the air lter from

where it was removed, and re-insert the air

lter back in place. Re-attach the black pipe

back onto the cylinder cover, and ensure all is

secure in place. Replace the air lter cover (15),

and secure the air lter knob (16) in a clock wise

direction to secure the air lter cover (15) back

in place.

Guide Bar:

1. Take o the guide bar (19) and maintain it by

removing any sawdust from the groove in the

guide bar (Fig AS).

2. Make sure that the oil port is not clogged. Oil

the nose sprocket at the tip of the guide bar (19)

(Fig AT).

3. Check for fuel and oil leakage and loose

fastenings, especially those securing the

handles and the guide bar (19).

If any defects are found, take the tool to an

authorised Service Agent.

4. A bar cover (31) is supplied with this chainsaw

and should be tted over the chain (20) and

guide bar (19) whenever the chainsaw is not

being used. This includes immediately after use,

transportation and service where possible.

The chain teeth are extremely sharp and could

create a safety hazard if the bar cover (31) is not

tted. Furthermore, the bar cover (31) provides

protection to the chain cutting edge when the

saw is not in use (Fig AU).

AS.

AR.

AQ.

AT.

Maintenance Maintenance

Transportation and Storage

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline FCS4800A Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info