Bedienungsanleitung Gardenline KSI-2200 (Seite 8 von 16) (Englisch)

724682

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

AFTER SALES SUPPORT

Tel.: 1800 909 909

www.globalpowerbrands.com email: help@globalpowerbrands.com

KSI 2200

AUS

stopped by activation of the hand guard 4, the motor will not be stopped.

This brake function is initiated by the back of your hand on the front

handle 2 pushing the hand guard. The proper function of the saw chain

brake shall be checked before each use of the saw. About every 10 hours

of operation, the chain brake should be checked for its proper function.

After the chain brake has been activated, wait for the motor to come to a

halt before you engage the clutch again. Do not unnecessarily activate the

chain brake as this may result in increased wear and tear.

CAUTION: No buttons should be pressed when the chain brake

is released (hand protection pulled back in the direction of the

handle and locked).

Always ensure before starting the chainsaw that the hand pro-

tection 4 is locked in the operating position. To do this, pull back

the hand protection in the direction of the handle.

5.2. Rundown brake

In accordance with the latest regulations, this chainsaw is equipped with

a mechanical rundown brake. This brake is connected to the chain brake

and stops the running chain after the chainsaw has been switched o .

It is activated by releasing the ON/OFF switch. The rundown brake

avoids injuries through the coasting of the chain.

5.3. Safety starting lock

The starting delay that is e ective for about 3 sec. after each switch-o

of the chainsaw provides for additional safety.

Thus, for your own safety, there is a delay of 3 seconds before the

device can be switched on again after each time it is switched o .

Only after this phase, the saw may be operated again by pushing the

locking button 15 and subsequently activating the operating switch

9, as described in the section ‘Switching on’.

5.4. Chain catch bolt

This chainsaw is  tted with a chain catch bolt (19). If the chain breaks

when the saw is in operation, the chain bolt will catch the loose chain

end and thus prevent injury to the operator‘s hand.

6. Instructions on working properly with the chainsaw

a) Felling a Tree

DIRECTION OF FALL

NOTCH

FELLING BACK CUT

2 INCHES

HINGE

2 INCHES

When bucking and felling operations are being performed by two or

impedance Z max at the point of connection (house service connection)

of max. 0.4 Ohm. The user must ensure that the device is only operated

on an electricity supply system meeting these requirements. If required,

system impedance data may be obtained from the local public utility.

Use only extension cords that are approved for outdoor use

and are not lighter than rubber-sheathed cables of type H07

RN-F according to DIN/VDE 0282 with a diameter of at least

1.5 sq. mm. They cords must be splash-proof. If the connection

cable of this device should be damaged it must be replaced by

a workshop named by the manufacturer only as this work re-

quires the use of special tools. Mobile devices for outdoor use

should be connected over a residual current operated device.

This chainsaw is  tted with a strain-relief device to provide extra

safety for the connection. First connect the device plug with the

connection line. Then form the connection line into a tight loop and

push this through the safety web on the lower side of the machine.

Hang the loop into the hook as shown in Fig. The plug connection is

now secure against automatic release.

4.4. Switching on

• Press with your thumbs the stopping button 15 on the left side of

the rear handle and then the operating switch 9.

• The stopping button 15 is used for unlocking the switch-on mechanism

and does not need to be pressed again after the device is switched on.

• To switch o the device, release switch 9.

Attention : The sawing chain will start running at high speed

immediately. When putting the saw down, make sure that the

chain never gets in touch with stones or metal objects.

5. Safety devices on your chain brake

5.1. Chain brake

This chainsaw is equipped with a mechanical brake for the chain. In the

case of uncontrolled movements, when the tip of the saw blade gets in

contact with wood or a solid object, the drive of the chain is immediately

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline KSI-2200 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info