Bedienungsanleitung Gardenline PM2006H (Seite 13 von 21) (Englisch)

724641

Zoom out

Zoom in

Vorherige Seite

1/21

Nächste Seite

45cc Petrol Chainsaw

AFTER SALES SUPPORT

e-mail: help@powertoolsupport.com

1800 909 909

MODEL: №. 53942 • 09/2018 • PM2006H

(toll free)

AFTER SALES SUPPORT

(toll free)

e-mail: help@powertoolsupport.com1800 909 909

45cc Petrol Chainsaw

MODEL: №. 53942 • 09/2018 • PM2006H

22 23

Stopping the Chainsaw

1. Release the throttle trigger (3).

2. Press down the on/o switch (4) to the “STOP”

position (Fig AC).

NOTE: Especially after the rst starting of the

chainsaw, the tension of the chain should be

checked. The chain will become loose on the rst

start up and will require adjustment. Refer to the

“Changing / Replacing the Guide Bar and Chain”

section.

Checking the Oil supply

Run the engine at medium speed and check that

the chain splatters a thin line of oil which can be

seen on the ground when the guide bar (19) is

pointed downwards (Fig AD). DO NOT ALLOW THE

TIP OF THE BAR touch ANY surface when checking

the oil ow. Keep the chain (20) and guide bar (19)

well clear of ANY surface. This visual thin line of oil

is normal and is an indication the oil system is oiling

the guide bar (19) and chain (20).

NOTE: For rst time use the oil may take a few

minutes to work through the oil system.

The oil pump is ONLY operating while the chain (20)

is rotating so at idle the oil is NOT being pumped

through the oil system. If there is no line of chain oil

after a few minutes, stop the engine immediately

and investigate the cause. The oil tank (6) could be empty or the oil supply

to the chain blocked. This may require removal of the guide bar (19) and

checking that the upper oil hole in the bar is clear of any blockages (Fig AE).

Adjusting the Carburettor

NOTE: It is recommended the carburettor adjustment is performed by a

service centre to ensure the correct setting for both safety and performance.

The carburettor is factory set and should not require adjustment.

6 . Hold the chainsaw securely on the ground by

placing one foot on the rear handle, one hand

secure on the front handle, and using your other

hand, slowly pull the recoil starter (11) 2 times so

that air and fuel is drawn into the engine slowly

(Fig AA).

7. Push the combination choke control / throttle lock

knob (10) back inwards (As now the engine has

been primed).

8. Again hold the chainsaw securely on the ground

by placing one foot on the rear handle, one hand

secure on the front handle, and using your other

hand pull at a steady and medium rate on the

recoil starter (11) (Fig AA).

9. Pull the throttle trigger upward to release the

throttle lock (this is engaged when you pull the

combination choke control / throttle lock knob (10) on).

10. To start cutting, release the front guard / chain brake (13), by pulling it

rmly towards the back of the chainsaw until a click is heard (Fig Y).

11. Press in the safety lever (2) then the throttle trigger (3), to commence

movement of the chain and start cutting (Fig AB).

Warm / Hot Starting the Chainsaw

Follow this procedure when starting the chainsaw if you have recently

stopped it and wish to restart it or have had to refuel or add oil etc.

1. Turn the on/o switch (4) to the “On” position as indicated by an “I” (Fig X).

2. Make sure the front guard / chain brake (13) is ON when starting for safety

by pushing it rmly towards the nose of the chainsaw bar until a click is

heard (Fig Y). This ensures the chain wont start spinning upon starting.

3. Press the priming bulb (36) 4 times or until the priming bulb (36) is full of

fuel.

4. Hold the chainsaw securely on the ground, by placing one foot on the rear

handle, one hand securing the front handle, and using your other hand,

pull at a steady and medium rate on the recoil starter (Fig AA).

AD.

AC.

AE.

Operation Operation

AB.

AA .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Gardenline PM2006H Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info