724641
14
Zoom out
Zoom in
Vorherige Seite
1/21
Nächste Seite
45cc Petrol Chainsaw
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 53942 • 09/2018 • PM2006H
(toll free)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
45cc Petrol Chainsaw
MODEL: №. 53942 • 09/2018 • PM2006H
24 25
Checking the operation of the clutch.
Each time the chainsaw is started, the operation of the clutch (38) should
be checked as per the following detail. The chain MUST rst be checked to
ensure correct tension adjustment before starting.
1. When attempting to start the chainsaw, the chain (20) should not be trying
to move around the guide bar (19) under the inuence of the recoil starter
(11). If it is trying to rotate around the guide bar (19), STOP the starting
process and take the saw to an authorised service centre.
2. If point 1 is correct and the chain (20) is not trying to rotate around the
guide bar (19), start the chainsaw as per the section in the manual “Starting
the Chainsaw”.
3. With the chainsaw operating and at idle (throttle lock (5) NOT engaged),
and ensuring the chain (20) is in a safe position with respect of other
persons and any objects, release the chain brake (13).
CHECK, the chain (20) should NOT be rotating around the guide bar (19) at
idle speed.
4. Operate the safety lever (2) and then accelerate the throttle trigger (3).
The chain (20) should start and rotate. The harder the throttle trigger (3)
is pulled, the faster the chain (20) will rotate. RELEASE the throttle trigger
(3) so the motor returns to the idle condition. The chain (20) MUST stop
rotating around the guide bar (19) when the motor of the saw is at idle.
5. If the chain (20) is constantly rotating when the motor of the saw is at idle,
the chainsaw should NOT be used and the chainsaw should be taken to an
authorised service centre for repair.
6. DO NOT use the chainsaw if the clutch (34) does not totally disengage
when the motor of the saw is at idle.
Re-setting the Chain Brake
The front guard / chain brake (13) operates automatically in the event of
kickback. In the event of a kickback, the guide bar (19) kicks up, the wrist of
the operator’s hand on the top handle knocks against the front guard / chain
brake (13) causing it to move forward thus activating the chain brake (13).
To reset the front guard / chain brake (13) this can be done manually by
pulling it rmly towards the back of the chainsaw until a click is heard. (Fig A).
CAUTION: Each time the chainsaw is used, check that the chain brake (13)
is operating correctly.
Operation
WARNINGS:
Always follow the safety instructions given at the front of this manual.
This chainsaw must only be used for cutting wood. It must not be used
for cutting other types of material. Do not use the chainsaw as a lever for
lifting, moving or splitting objects.
Do not attach the chainsaw to a xed stand.
Do not attach any devices to the chainsaw other than those specied by
the manufacturer.
Be aware of any local or national restrictions when using this appliance.
This could include, but not restricted to, times of operation, location of
operation, or work place operation.
Helpful Hints
Do not force the chainsaw into the cut. Apply only light pressure whilst
running the engine at full throttle.
If the chain (20) gets caught in the cut, do not try to remove it by twisting
the guide or pulling forcibly. Use a lever or wedge to open up the cut so
that the chain is freed.
Vibration
Vibration white nger may occur in operators using hand held vibrating tools
such as chainsaws. Continual vibration can cause both vascular damage and
also Nerve Damage to the operator.
The following guidelines can reduce the risk:
- Limit the use of vibrating tools.
- Hold vibrating tools as loosely as possible and in varying positions.
- Ensure tools are well maintained; make sure cutting blades are kept sharp
to maintain eciency, and replace worn parts.
- Use tools correctly, and use the right tool for the job (to do the job more
quickly and reduce exposure time).
- Store tools so that they do not have very cold handles when next used.
- Use anti-vibration gloves.
- Take regular breaks of at least 10 minutes every hour away from the tool.
Operation Operation
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Gardenline PM2006H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info