Bedienungsanleitung Garmin Alpha100 TT 10 (Seite 10 von 26) (Englisch)

657463

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Select Setup > Location Alerts > Add Alert > Radius.

Select the unit of measurement.

Enter the radius distance, and select .

Editing Location Alerts

Select Setup > Location Alerts.

Select an alert.

Select an option:

• Select Disable to turn off notifications for this alert.

• Select Set Alert Type to set the way the device notifies

you for this alert.

• Select Set Alert Mode to set the notification to sound on

exit, entrance, or both.

• Select Delete to remove the alert.

Dog Training

You should research and investigate the training methods best

suited for you, your dog, and your needs. This manual provides

some basic guidelines for training, but each dog has unique

training needs.

When used properly, the Alpha training system is a very

effective training tool to aid your dog in reaching its full potential.

The use of the training system should be part of an overall

training program.

Begin training your dog on a leash, without the Alpha training

system. You should train your dog how to heel, sit, and come to

you. After the dog understands these three basic commands,

you can begin training with the dog collar device and the leash.

Finally, when the dog consistently obeys commands using the

leash and collar, you may be able to remove the leash to train

with only the dog collar device.

Selecting and Installing the Contact Points

For best results, select the correct contact points based on your

dog's coat.

Select the correct contact point length for your dog's coat

type:

• For dogs with thicker coats, use the longer contact points.

• For dogs with shorter coats, use the shorter contact

points.

If necessary, use the included wrench to remove the contact

points.

Twist the contact points into the collar.

Tighten with the included wrench, but do not overtighten.

When you put the collar on the dog, make sure that the contact

points are tight against the neck (page 4).

Removing the Contact Points

When you are not training the dog using the training keys,

remove the contact points.

Use the included wrench to remove both contact points.

Place the cap over the contact point holes.

Setting Up the Training Keys for One

Intensity Level

Before you can assign the training keys to a dog, you must add

the dog to the handheld device (page 3).

By default, the training keys are set to the lowest stimulation

setting, with momentary (M), continuous (C), and tone (T) for

each key. This mode is most useful when training only one dog.

When training multiple dogs, it may be helpful to customize a

training key for each dog and for each intensity level

(page 6).

Select Setup > Training > Training Buttons.

Select the area at the top of the screen directly below the

keys.

Select the intensity level for the keys.

If you are using traditional stimulation mode, select LOW,

MED, or HI.

Select .

In this mode, the left key provides momentary simulation. The

center key provides continuous stimulations. The right key

provides a tone.

Customizing the Training Keys

Before you can assign the training keys to a dog, you must add

a dog to the handheld device (page 3).

You can change the mode of the training keys to customize

each key for a specific stimulation intensity level and for each

dog. This mode is most useful when training multiple dogs.

When training only one dog, it might be more useful to set only

the intensity level (page 6).

Select Setup > Training > Training Buttons > Change

Mode.

Select the top of the screen directly under the key you are

customizing.

Select the dog you want to train with this key.

Select an intensity level for the key.

If you are using traditional stimulation mode, select LOW,

MED, or HI.

Select momentary (M), continuous (C), or tone (T).

Repeat steps 3-6 for all three keys.

If you need to train with more than three keys, select >

Insert Page, and program the additional keys.

Select .

Basic Training Commands

You should begin training your dog with a few basic commands

without using the Alpha training system to correct the dog. You

should train the three basic commands in the following order:

"heel," "sit," and "here."

During initial training, you should put the dog collar device on

the dog, but the device should be turned off. This allows the dog

to get used to the device before you start using it to correct the

dog. This also helps to prevent "collar-wise" behavior

(page 7).

Initially, you should keep the training sessions short and only

train one command during a session. This way, the dog is less

likely to become confused and training should progress more

quickly. Pay close attention while training the dog, so you can

begin to learn when to go faster or slower, and when to take a

break.

6 Dog Training

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin Alpha100 TT 10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info