Bedienungsanleitung Garmin echoMAP 70dv (Seite 24 von 30) (Englisch)

590095

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Select Settings > My Vessel > Keel Offset.

Select or based on the location of the transducer.

Enter the distance measured in step 1.

Setting the Water Temperature Offset

Before you can set the water temperature offset, you must have

a NMEA 0183 water-temperature sensor or a temperature-

capable transducer to measure water temperature.

The temperature offset compensates for the temperature

reading from a temperature sensor.

Measure the water temperature using the temperature sensor

or temperature-capable transducer that is connected to the

chartplotter.

Measure the water temperature using a different temperature

sensor or a thermometer that is known to be accurate.

Subtract the water temperature measured in step 1 from the

water temperature measured in step 2.

This is the temperature offset. Enter this value in step 5 as a

positive number if the sensor connected to the chartplotter

measures the water temperature as being colder than it

actually is. Enter this value in step 5 as a negative number if

the sensor connected to the chartplotter measures the water

temperature as being warmer than it actually is.

Select Settings > My Vessel > Temp. Offset.

Enter the temperature offset calculated in step 3.

Communications Settings

NOTE: Some settings and options require additional charts or

hardware.

Select Settings > Communications.

Serial Port: Sets the input/output format for the serial port to

use when connecting the chartplotter to external NMEA

devices, computers, or other Garmin devices.

NMEA 0183 Setup: Sets the NMEA 0183 sentences the

chartplotter transmits, how many digits to the right of the

decimal point are transmitted in a NMEA output, and how

waypoints are identified (NMEA 0183 Settings).

NMEA 0183

The chartplotters support the NMEA 0183 standard, which is

used to connect various NMEA 0183 devices, such as VHF

radios, NMEA instruments, autopilots, wind sensors, and

heading sensors.

To connect the chartplotter to optional NMEA 0183 devices, see

the chartplotter installation instructions.

The approved NMEA 0183 sentences for the chartplotter are

GPAPB, GPBOD, GPBWC, GPGGA, GPGLL, GPGSA, GPGSV,

GPRMB, GPRMC, GPRTE, GPVTG, GPWPL, GPXTE, and

Garmin proprietary sentences PGRME, PGRMM, and PGRMZ.

This chartplotter also includes support for the WPL sentence,

DSC, and sonar NMEA 0183 input with support for the DPT

(depth) or DBT, MTW (water temperature), and VHW (water

temperature, speed, and heading) sentences.

NMEA 0183 Settings

Select Settings > Communications > NMEA 0183 Setup.

Sounder: Enables NMEA 0183 output sentences for the

sounder (if applicable).

Route: Enables NMEA 0183 output sentences for routes.

System: Enables NMEA 0183 output sentences for system

information.

Garmin: Enables NMEA 0183 output sentences for Garmin

proprietary sentences.

Posn Precision: Adjusts the number of digits to the right of the

decimal point for transmission of NMEA output.

Waypoint IDs: Sets the device to transmit waypoint names or

numbers via NMEA 0183 while navigating. Using numbers

may resolve compatibility issues with older NMEA 0183

autopilots.

Diagnostics: Displays NMEA 0183 diagnostic information.

Defaults: Restores the NMEA 0183 settings to the original

factory defaults.

Setting Alarms

Navigation Alarms

Select Settings > Alarms > Navigation.

Arrival: Sets an alarm to sound when you are within a specified

distance or time from a turn or a destination.

Anchor Drag: Sets an alarm to sound when you exceed a

specified drift distance while anchored.

Off Course: Sets an alarm to sound when you are off course by

a specified distance.

System Alarms

Alarm Clock: Sets an alarm clock.

Device Voltage: Sets an alarm to sound when the battery

reaches a specified low voltage.

GPS Accuracy: Sets an alarm to sound when the GPS location

accuracy falls outside the user-defined value.

Units Settings

Select Settings > Units.

System Units: Sets the unit format for the device.

Variance: Sets the magnetic declination, the angle between

magnetic north and true north, for your present location.

Heading: Sets the direction references used in calculating

heading information. True sets geographic north as the north

reference. Grid sets grid north as the north reference (000º).

Magnetic sets the magnetic north as the north reference.

Position Format: Sets the position format in which a given

location reading appears. Do not change this setting unless

you are using a map or chart that specifies a different

position format.

Map Datum: Sets the coordinate system on which the map is

structured. Do not change this setting unless you are using a

map or chart that specifies a different map datum.

Pressure Ref. Time: Sets the reference time used to calculate

the barometer trend. The trend is indicated in the barometer

field.

Time Format: Sets a 12-hour, 24-hour, or UTC time format.

20 Device Configuration

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Garmin echoMAP 70dv Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info